DS800SL-3 Artesyn Embedded Technologies

Embedded Power for Business-Critical Continuity Rev. 12.17.13 DS800SL Series 1 of 8 DS800SL Series 800 Watts Bulk Front End Total Output 800 Watts Power: +5.0 Vdc Stand-by Electrical Speci cations Special Features Input 800 W output power Input ra nge (operating): 90 - 264 Vac 19.05 W/cu-in Input range (nominal): 115 / 230 Vac 1U X 54.5 mm form factor (slimline) N + 1 redundant Hot-swap Frequency: 47 - 63 Hz Internal ORing Input fusing: Internal 10 A fuses 5.0 V housekeeping Inrush current: 40 A peak Either hot or cold start High ef ciency 92% 200 Vac, Power factor: 0.99 typical Meets EN61000-3-2 50% load (Climate Savers Gold) Harmonics: Meets IEC 1000-3-2 requirements Variable speed smart fans EMI Class B Input current: 10 A RMS max input current At 100 Vac EN61000 Immunity Holdup time: 10 ms minimum for main O/P At full rated load Available in two air ow directions Undervoltage lockout: 85 3.0 Vac Turn-on voltage 80 3.0 Vac Turn-off voltage Overvoltage lockout: N/A Leakage current: < 1.0 mA At 264 Vac On/Off power switch: N/A Power line transient: MOV directly after the fuse Ordering Information Main Output Standby Output Air ow Direction DS800SL-3 12V 5VSB 4.0A Forward (output to handle) 1 DS800SL-3-001 12V 5VSB 4.0A Reverse (handle to output) Safety 1 Output power derating applies. See power derating curve. UL/cUL 60950 -1 CSA 60950-1 VDE 60950-1 China CCC CB Scheme Report/CertEmbedded Power for Business-Critical Continuity Rev. 12.17.13 DS800SL Series 2 of 8 Efficiency Curve 800 W DS Slim DS800SL-3-001 Power Derating 92.0% 820 90.0% 800 780 88.0% 760 740 230 Vac, 50 Hz 720 100Vac 86.0% 115 Vac, 60 Hz 700 110Vac 680 84.0% 230Vac 660 640 82.0% 620 0 1020304050 80.0% Ambient Temperature (degC) 0.0 100.0 200.0 300.0 400.0 500.0 600.0 700.0 800.0 900.0 Output Power W Output Output rating: 12 V 66.7 A 800 W 90 - 264 Vac 5.0 Vsb 4 A 20 W Setpoint: 12.0 V Total regulation range: 12 V 1% Line/load/transient when measured at output 5.0 Vsb 3% connector Rated load: 800 W maximum No derating over operating temp range for forward air Minimum load: 12 V 0.5 A No load operation shall not damage the power supply 5.0 Vsb 0.0 A Output noise (PARD): 120 mV Max P-P 12.0 V output 100 mV Max P-P 5.0 Vsb output Measured with a 0.1 uF ceramic and 10 uF tantalum capacitor on any output 20 Mhz Output voltage overshoot: 600 mV 12 V main 1 A/uSec slew rate 250 mV 5.0 standby Transient response: +/- 5% of regulation range 50% load step 1 A/us Step load valid between 10% to 100% of output rating Recovery time to within 1% of set point at onset of transient Max units in parallel: Up to 6 Short circuit protection: >130% of rated output current Output to return Remote sense: Compensation up to 100 mV Output isolation: Standard per Safety Requirements Forced load sharing: To within 10% of all shared outputs Digital sharing control Overload protection (OCP): 120% to 130% 12 V output 120% to 170% 5.0 Vsb output Overvoltage protection (OVP): 110% to 120% 12 V output 110% to 125% 5.0 Vsb output Overtemperature protection: 10 - 15 C above safe operating area Both PFC and output converter monitored Efficiency Power Rating