POWER LPQ142 Series Data Sheet 145 Watts Total Power: 110 - 145 Watts Input Voltage: 85 - 264 Vac 120 - 300 Vdc of Outputs: Quad Special FeaS Active power factor correction IEC EN61000-3-2 compliance Adjustable outputs on 1, 3 & 4 Remote sense on main output Single wire current sharing Electrical Specifications Power fail and remote inhibit Input Built-in EMI filter Low output ripple Input ra nge 85 - 264 Vac 120 - 300 Vdc Overvoltage protection Frequency 47 - 67 Hz Overload protection Inrush current 38 A max, cold start 25 C Thermal overload protection Efficiency 75% typical at full load Adjustable floating 4th output EMI filter Meets FCC Class B conducted RoHS compliant CISPR 22 Class B conducted Optional cover (-C suffix) EN55022 Class B conducted Optional fan cover (-CF suffix) VDE 0878 PT3 Class B conducted Power factor 0.99 typical SaF Safety ground 1.0 mA 50/60 Hz, 264 Vac input leakage current VDE 60950 Output UL 60950 CB Certificate and report Maximum power 80 W convection (60 W with cover -C) 145 W with 30 CFM forced air CSA 60950 (100 W with cover -C) CE Mark (LVD) Adjustment range 3.3 - 5.5V on main -12 - 15V on 3rd output NEMKO EN 60950/EMKO-TUE 3.3 - 25 V on 4th output Hold-up time 20 ms 175 W load at nominal line Overload protection Short circuit protection on all outputs. Case overload protected 110-145% above peak rating Overvoltage protection Tracks outputs 1, 3 & 4 10 to 35% ety tureLPQ142 Series Data Sheet Logic Control AC power failure TTL logic signal goes high 100 - 500 msec after V1 output It goes low at least 4 msec before loss of regulation Remote inhibit Requires contact closure to inhibit outputs Remote sense Compensates for 0.5 V lead drop min. Will operate without remote sense connected. Reverse connection proteced. DC - OK TTL logic signal goes high after main output is in regulation. It goes low when there is a loss of regulation Environmental Specifications Operating temperature 0 to 50 C ambient. Derate each output 2.5% per degree from 50 to 70 C (except for -C version). Storage temperature -40 C to +85 C Temperature coefficient 0.4% per C Electromagnetic susceptibility Designed to meet IE61000-4, -2, -3, -4, -5, -6, -8, -11, Level 3 Humidity Operating non-condensing 5% to 95% Vibration Three orthogonal axes, sweep at 1 oct/min, 5 min. dwell at four major resonances 0.75G peak 5Hz to 500Hz, operational MTBF demonstrated >550,000 hours at full load and 25C ambient conditions Ordering Information Maximum Load Model Output Minimum Maximum Load with Ripple P/P 1 2 with 30CFM Peak Load Regulation 3 Number Voltage Load Convection Cooling (PARD) Forced Air LPQ142 5 V (3.3 - 5.5 V) 0 A 12 A 25 A 27 A 2% 50 mV 12 V 0 A 5 A 6 A 9 A 3% 120 mV -12V (-12 -15 V) 0 A 1 A 1.5 A 2 A 3% <1% 3.3-25 V 0.5 A 1.5 A 4.5 A 5 A 3% <50mV or 1% 1. Peak current lasting <30 seconds with a maximum 10% duty cycle. 2. At 25 C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3. Peak-to-peak with 20 MHz bandwidth and 10 F in parallel with a 0.1 F capacitor at rated line voltage and load ranges. 4. Fourth (4th) output adjustable 3.3 - 25 V factory set at 5 V. 5. *Minimum loads are required when output set below 5 Volts 6. Remote inhibit resets OVP latch 7. This product is a Component Power Supply and is only for inclusion by professional installers within other equipment and must not be operated as a standalone product. EMC compliance to appropriate standards must be verified at the system level. This product is for sale to OEMs and System Integrators, including through Distribution Channels. It is not intended for sale to End Users. Note: -C suffix added to the model number indicates cover option. -CF suffix added to the model number indicates fan cover option. Pin Assignments Pin Assignments Mating Connectors (SK1) AC Input Molex 09-50-8051 (USA SK1 PIN 1 Ground SK6 PIN 1 N/C Molex 09-91-0500 (UK) PIN 3 Neutral PIN 2 DC OK PINS: 08-58-0111 PIN 5 Line PIN 3 N/C Molex 09-50-8061 (USA) (SK2) Aux DC SK2 PIN 1 +12 V PIN 4 V1 SWP Output Molex 09-91-0600 (UK) PIN 2 Common PIN 5 Common PINS: 08-58-0111 PIN 3 -12 V PIN 6 +V1 sense Molex 90142-0010 (USA) (SK6) Control PIN 4 Common PIN 7 Sense common Signals PINS: 90119-2110 or Amp: 87977-3 PIN 5 +5 V to +25 V (float) PIN 8 + inhibit PINS: 87309-8 PIN 6 Common (float) PIN 9 - inhibit (SK4) Main Output Molex BB-19141-0058 SK4 TB-1 Common PIN 10 Power fail Artesyn Embedded Power connector kit TB-2 +5 V 70-841-017, includes all of the above.