Total Power: 110-150 Watts Input Voltage: 85-132 / 170-264 VAC 150 Watts 220-300 VDC of Outputs: Quad LPQ150 Series Electrical Specs Input Input range 85-132 VAC or 170-264 VAC automati- cally selected. 220-300 VDC Frequency 47-63 Hz Inrush current 38 A max, cold start 25C Efficiency 75% typical at full load EMI filter Meets FCC Class B conducted CISPR 22 Class B conducted EN55022 Class B conducted VDE 0878 PT3 Class B conducted Safety ground leakage current 0.5 mA 50/60 Hz, 264 VAC input Special Features Output Maximum power 110 W convection (75 W with cover) Auto ranging input 150 W with 30 CFM forced air Remote sense on main output (130 W with cover) Remote inhibit Single wire current sharing Adjustment range 5% on main 5-25 V on 4th output Power fail on LPQ 152 & LPQ 153 Built-in EMI filter Cross regulation 2% on output 1 3% on outputs 2, 3 Low output ripple & 4 135 khz switching frequency Hold-up time 20 ms 110 W load at nominal line Overvoltage protection Overload protection Short circuit protection on all outputs. Overload protection Case overload protected 110-145% Adjustable floating 4th output above peak rating (On LPQ152 and LPQ153 models) Overvoltage protection 5.7-6.7 VDC on main output Optional cover (-C suffix). See page 64. Environmental Logic Control Power failure TTL logic signal goes high 50-150 msec after 5 V output. It goes low at Operating temperature: 0 to 50C ambient least 3 msec before loss of regulation derate each output at 2.5% per degree from Remote inhibit Requires an external TTL high signal to 50 to 70C inhibit outputs Electromagnetic susceptibility: designed to meet Remote sense Compensates for 0.5 V lead drop min. IEC 801, -2, -3, -4, -5, -6, Level 3 Will operate without remote sense Humidity: Operating non-condensing connected. Reverse connection 5% to 95% protected. Vibration: Three orthogonal axes, sweep at 1 oct/min, 5 min. dwell at four major resonances 0.75 G peak 5 Hz to 500 Hz, operational Safety Storage temperature: -40 to 85C VDE 0805/EN60950 (IEC950) 11774-3336-1260 (LC 88585) Temperature coefficient: .04% per C UL UL1950 EI32002 CSA CSA 22.2-234 Level 3 LR53982 MTBF demonstrated: >550,000 hours at full load NEMKO EN 60950/EMKO-TUE P95102999 and 25C ambient condition (74-sec) 203 CB Certificate and report 2061 CE Mark (LVD) rev 12.10.03 Technical Support: (888) 41-ASTEC or (407) 241-2752 Americas: (760) 930-4600 Europe (UK) 44 (1384) 842-211 Asia (HK) 852-2437-9662 114LPQ150 Series ASIA EUROPE AMERICAS Units 2111-2116, Level 21 Astec House, Waterfront Business Park 5810 Van Allen Way Tower1, Metroplaza Merry Hill, Dudley Carlsbad, CA 92008 223, Hing Fong Road West Midlands, DY5 1LX, UK Telephone: 760-930-4600 Fwai Fong, New Territories Telephone: 44 (1384) 842-211 Facsimile: 760-930-0698 Hong Kong Facsimile: 44 (1384) 843-355 Telephone: 852-2437-9662 Facsimile: 852-2402-4426 Ordering Information 2 Model Output Minimum Maximum Load with Maximum Load with Peak Regulation Ripple 1 3 Number Voltage Load Convection Cooling 30 CFM Forced Air Load P/P (PARD) LPQ152 5 V 2 A 15 A 22 A 30 A 2% 50 mV 12 V .1 A 6 A 8 A 10 A 3% 120 mV -12 V .1 A 2 A 2.5 A 3 A 3% 120 mV 5-25 V 0 A 2.5 A 3 A 3 A 3% 240 mV, max. LPQ153 5 V 2 A 15 A 22 A 30 A 2% 50 mV 15 V .1 A 4.8 A 6.4 A 8 A 3% 150 mV -15 V .1 A 1.6 A 2 A 2.4 A 3% 150 mV 5-25 V 0 A 2.5 A 3 A 3 A 3% 240 mV, max. LPQ154 5 V 2 A 15 A 22 A 30 A 2% 50 mV 12 V .1 A 6 A 8 A 10 A 3% 120 mV -12 V .1 A 2 A 2.5 A 3 A 3% 120 mV 24 V .5 A 3.5 A 4.5 A 5 A +10 / -5% 240 mV 1. Peak current lasting <30 seconds with a maximum 10% duty cycle. 2. At 25C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3. Peak-to-peak with 20 MHz bandwidth and 10 F in parallel with a 0.1 F capacitor at rated line voltage and load ranges. 4. 4th output adjustable 5-25 V factory set at 5 V. 5. Minimum loads are required. Note: -C suffix added to the model number indicates cover option. SK1 8765 Pin Assignments 6-32 UNC (8 places) SK2 SK3 1234 .5625 Connector LPQ152 LPQ153 LPQ154 2 1 987654321 SK1 PIN 1 INHIBIT -ve INHIBIT -ve INHIBIT -ve PIN 2 INHIBIT +ve INHIBIT +ve INHIBIT +ve PIN 3 +12 V +15 V +12 V PIN 4 No Connection No Connection No Connection PIN 5 COMMON COMMON COMMON PIN 6 -SENSE -SENSE -SENSE PIN 7 +SENSE +SENSE +SENSE PIN 8 I SHARE I SHARE I SHARE SK2 PIN 1,2 +12 V +15 V +12 V PIN 3,4,5 COMMON COMMON COMMON 7.4 PIN 6 -12 V -15 V -12 V (188.0) PIN 7 POK POK POK PIN 8 +5 V to +25 V (Float) +5 V to +25 V (Float) +24 V 8.5 PIN 9 COMMON (Float) COMMON (Float) COMMON (216.0) SK3 TB-1 COMMON COMMON COMMON TB-2 +5 V +5 V +5 V SK4 PIN 1 GROUND GROUND GROUND PIN 3 LINE LINE LINE PIN 5 NEUTRAL NEUTRAL NEUTRAL Notes Mating Connectors 1. Specifications subject to change (SK4) AC Input: Molex 09-50-8051 (USA) without notice. Molex 09-91-0500 (UK) 2. All dimensions in inches (mm), 5 3 1 PINS: 08-58-0111 .75 (19.0) tolerance is 0.02. 3. Specifications are for convection SK4 (SK2) Aux DC Output/Power fail: 1.5 4.25 rating at factory settings unless (38.1) Molex 09-50-8091 (USA) (108.0) otherwise stated. Molex 09-91-0900 (UK) 4. Remote inhibit requires an external PINS: 08-58-0111 5V 10mA to activate. (SK1) Remote sense/Remote inhibit: 5. Mounting (6-32) maximum insertion Molex 51110-0851 (USA) depth is 0.12. PINS: 503-94-8100 6. Warranty: 2 year 7. Weight: 1.75 lb. / 0.80 kg .875 2.5 (22.25) (63.5) Astec Connector Kit 70-841-010, includes al of the above. www.astecpower.com 115 DO NOT ADJ 4th O/P ADJ 5V O/P ADJ