Embedded Power for Business-Critical Continuity Rev. 01.14.12 43 LPQ200-M Series 1 of 3 LPQ200-M Series 200 Watts Total Power: 100 - 200 Watts Input Voltage: 90 - 264 Vac of Outputs: Quad Electrical Specifications Special Features Medical and ITE safeties Input Active power factor correction Input range: 90 - 264 Vac 120 - 300 Vdc 3 x 5 footprint Frequency: 47 - 63 Hz Less than 1U high Inrush current: 50 A max., cold start 25 C, 230 Vac input EN61000-3-2 compliant Efficiency: 84% typical at full load Remote sense EMI/RFI: FCC Class B conducted CISPR22 Class B conducted Power fail EN55022 Class B conducted VDE0878PT3 Class B conducted Adjustable outputs 275 uA 50/60 Hz, 264 Vac input Built-in Class B EMI filter Safety ground Overvoltage protection leakage current: Overload protection Output Thermal overload protection Maximum power: 100 W for convection 200 W with 30CFM forced air LPX200 enclosure kit available Adjustment range: All outputs -20%, +10%, except for the 3.3 V output which will be -15%, +10% (LPQ201-M) Hold-up time: 16 ms 200 W load, 120 Vac input Short circuit protection on all outputs. V1, V2 & V3 overload protected Overload protection: 110 - 160%. V4 is 150 - 250% above rating Overvoltage protection: 30 - 50% above nominal output on V1 (and V2 on LPQ202) Logical Control Power failure: Active low logic signal goes high 100-500 msec after main output it goes low at least 6 msec before loss of regulation Remote sense: Compensates for 0.5 V lead drop min. Will operate without remote sense connected. Reverse connection protected. Safety TUV 60950, 60601-1 UL 60950, 60601-1 CSA 60950, 60601-1 CB Certificate & report CE Mark (LVD)Embedded Power for Business-Critical Continuity Rev. 01.14.12 43 LPQ200-M Series Environmental Specifications 2 of 3 Operating temperature: 0 to 50 C ambient derate each output as 2.5% per degree from 50 to 70 C. -20 C start up Storage temperature: -40 C to +85 C Electromagnetic Designed to meet EN61000-4 susceptibility: -2, -3, -4, -5, -6, -8, -11 Level 3 Humidity: Operating non-condensing 10% to 90% RH, non-operating, non-condensing 10 - 95% Vibration: IEC68-2-6 to the levels of IEC721-3-2 MTBF calculated: 516,000 hours at full load and 25 C ambient conditions. 230 Vac input, Bellcore Ordering Information Model Output Minimum Maximum Load with Maximum Load with Peak Ripple 2 Regulation 3 Number Voltage Load Convection Cooling 30CFM Forced Air Load P/P (PARD) +3.3 V 0 A 13 A 18 A 20 A 2% 50 mV +5 V 0 A 13 A 18 A 20 A 5% 50 mV LPQ201-M +12 V 0 A 5 A 9 A 10 A 5% 120 mV -12 V 0 A 1 A 2 A 2.5 A 5% 120 mV +5 V 0 A 13 A 18 A 20 A 2% 50 mV +12 V 0 A 5 A 9 A 10 A 5% 120 mV LPQ202-M +24 V 0 A 1.5 A 3 A 3.5 A 7% 240 mV -12 V 0 A 1 A 2 A 2.5 A 5% 120 mV 1. Peak current lasting < 30 seconds with a maximum 10% duty cycle. 2 . At 25 C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3 . Peak-to-peak with 20 mHz bandwidth and 10 F (tantalum capacitor) in parallel with a 0.1 F capacitor at rated line voltage and load ranges. Mating Connectors Pin Assignments AC Input (SK1): Molex 09-50-8031 (connector) Connector LPQ200-M PINS: 08-52-0113 SK1 Pin 1 Neutral AC Ground: Molex 01-90020001 Pin 3 Line DC Output (SK2): Terminal block SK2 Pin 1 V1 OUT Wire size based on Cable Ampacity/AWG Pin 2 V2 OUT Control Signals Molex 90142-0010 (USA) Pin 3 GND OUT (SK3): PINS: 90119-2110 or Pin 4 GND OUT LANDWIN: 2580S0803 Pin 5 GND OUT PINS: 2583T021V Pin 6 GND OUT Emerson Network Power Connector Kit 70-841-027, includes all of the above. Pin 7 V3 OUT 1. Specifications subject to change without notice. Pin 8 V4 OUT 2. All dimensions in inches (mm), tolerance is 0.02 ( 0.5 mm) SK3 Pin 1 +V1 Remote sense 3. Mounting holes MH1 and MH2 should be grounded for EMI purposes. Pin 2 -V1 Remote sense 4. Mounting hole MH1 is safety ground connection. Pin 3 N/C 5. Specifications are for convection rating at factory settings at 115 VAC input, 25 C unless otherwise stated. Pin 4 N/C 6. This power supply requires mounting on metal Pin 5 +Power fail standoffs 0.20 (5 m) in height. 7. Warranty: 2 years Pin 6 Common Pin 7 N/C 8. Weight: 1.5 lbs/0.68 kg Pin 8 Common Pin 9 +V2 Remote Sense (LPQ201-M only) Pin 10 -V2 Remote Sense (LPQ201-M only)