43 SERIES 43 Series - Low profile PCB relays 10 - 16 A 1 Pole - Low profile (15.4mm height) 43.41 43.41-0300 43.61-0300 43.41 - 1 Pole, 10A (3.2mm pin pitch) 43.41-0300- 1 P ole NO, 10A (5mm pin pitch) 43.61-0300 - 1 Pole NO, 16A (5mm pin pitch) A PCB mount - direct or via PCB socket (43.41 version) Sensitive DC coil: - 250mW (10A version) - 400mW (16A version) Very high coil-contact isolation 10mm, 6kV (1.2/50s) Cadmium Free contacts (preferred version) 3.2mm contact pin pitch 5mm contact pin pitch 5mm contact pin pitch Flux proof: RT II standard, (RT III option) 1 Pole CO, 10A 1 Pole NO, 10A 1 Pole NO, 16A PCB direct or via socket PCB mount PCB mount 43.41 43.41-0300 43.61-0300 For UL tingsra see : Copper side view Copper side view Copper side view General technical information page V Contact specification Contact configuration 1 CO (SPDT) 1 NO (SPST-NO) 1 NO (SPST-NO) Rated current/Maximum peak current A 10/15 10/15 16/25 Rated voltage/ Maximum switching voltage VAC 250/400 250/400 250/400 Rated load AC1 VA 2500 2500 4000 Rated load AC15 (230VAC) VA 500 500 750 Single phase motor rating (230VAC) kW Breaking capacity DC1: 30/110/220 V A 10/0.3/0.12 10/0.3/0.12 16/0.3/0.12 Minimum switching load mW (V/mA) 300 (5/5) 300 (5/5) 300 (5/5) Standard contact material AgNi AgNi AgNi Coil specification Nominal voltage (U ) VAC (50/60Hz) N VDC 3 - 6 - 9 - 12 - 18 - 24 - 36 - 48 3 - 6 - 9 - 12 - 18 - 24 - 36 - 48 12 - 24 - 48 Rated power AC/DC VA (50Hz)/W /0.25 /0.25 /0.4 Operating range AC DC (0.71.5)U (0.71.5)U (0.71.2)U N N N Holding voltage AC/DC /0.4U /0.4U /0.4U N N N Must drop-out voltage AC/DC /0.05U /0.05U /0.05U N N N Technical data 6 6 6 Mechanical life AC/DC cycles /1010 /1010 /1010 3 3 3 Electrical life at rated load AC1 cycles 10010 10010 5010 Operate/release time ms 6/4 6/2 6/2 Insulation between coil and contacts (1.2/50s) kV 6 (10mm) 6 (10mm) 6 (10mm) Dielectric strength between open contacts VAC 1000 1000 1000 Ambient temperature range C 40+85 40+85 40+85 Environmental protection RT II RT II RT II Approvals (according to type) 1 I-2014, www.findernet.com43 SERIES 43 Series - Low profile PCB relays 10 - 16 A Ordering information Example: 43 series low-profile PCB relay, 1 CO (SPDT), 24VDC coil. A B C D A 4 3 . 4 1 . 7 . 0 2 4 . 2 0 0 . 0 Series A: Contact material D: Special versions 0 = AgNi 0 = Flux proof (RT II) Type 2 = A gCdO 1 = W ash tight (RT III) 4 = PCB - 3.2mm pinning 4 = AgSnO2 (CO/SPDT, 10A) 5 = AgNi + Au C: Options PCB - 5mm pinning 0 = None (NO/SPST-NO, 10A) B: Contact circuit 6 = PCB - 5mm pinning 0 = CO (SPDT) - (for 43.41 only) (NO/SPST-NO, 16A) 3 = NO (SPST) No. of poles 1 = 1 pole Coil version 7 = S ensitive DC (only for 43.41) Selecting features and options: only combinations in the same row are possible. 9 = DC (only for 43.61) Preferred selections for best availability are shown in bold. Coil voltage Type Coil version A B C D See coil specifications 43.41 sensitive DC 0 - 2 - 4 - 5 0 - 3 0 0 - 1 43.61 DC 0 - 2 - 4 0 - 3 0 0 Technical data Insulation according to EN 61810-1 Nominal voltage of supply system VAC 230/400 Rated insulation voltage VAC 250 400 Pollution degree 3 2 Insulation between coil and contact set Type of insulation Reinforced (10 mm) Overvoltage category III Rated impulse voltage kV (1.2/50s) 6 Dielectric strength VAC 4000 Insulation between open contacts Type of disconnection Micro-disconnection Dielectric strength VAC/kV (1.2/50s) 1000/1.5 Conducted disturbance immunity Burst (550)ns, 5kHz, on A1 - A2 EN61000-4-4 level 4 (4kV) Surge (1.2/50s) on A1 - A2 (differential mode) EN61000-4-5 level 3 (2kV) Other data Bounce time: NO/NC ms 3/6 Vibration resistance (555)Hz: NO/NC g 15/3 Shock resistance g 15 Power lost to the environment without contact current W 0.25 (43.41) 0.4 (43.61) with rated current W 1.3 (43.41) 2 (43.61) Recommended distance between relays mounted on PCB mm 5 2 I-2014, www.findernet.com