CYBLE-012011-EVAL Infineon

EZ-BLE PROC EVALUATION BOARD CYBLE-012011-EVAL The EZ-BLE PRoC Evaluation Board (CYBLE-012011-EVAL) enables you to evaluate and develop applications on the EZ-BLE PRoC Modules (CYBLE-012011-00 and CYBLE-012012-10). The EZ-BLE PRoC Module is a fully-integrated, fully-certi ed, 14.5 mm x 19.2 mm x 2.0 mm, programmable, Bluetooth Smart module designed to reduce your time-to-market. For more information, visit: www.cypress.com/EZ-BLEModule - EZ-BLE Module home page www.cypress.com/EZ-BLEEval - EZ-BLE PRoC Evaluation Board kit page www.cypress.com/go/AN96841 - Getting started guide EZ-BLE PROC Module J5 Header J2 Header (Bottom side) Cmod NC NC GND VDD P3 6 P3 7 NC NC P3 4 P3 5 NC NC P1 0 VREF P3 2 P3 3 NC NC NC NC P4 0 P5 1 P0 6 P1 4 NC P5 0 P0 7 NC XRES P1 5 P2 6 P3 5 GND P1 7 P2 4 P0 4 VDD P1 6 P2 2 P2 3 J6 Header P2 0 P0 5 VDDR GND VDD VDDR J1 Header (Bottom side) J3 Header J4 MiniProg3 10-pin Programming Header Fig 1: CYBLE-012011-EVAL Pinout Description Note: To use the CYBLE-012011-EVAL board, you must separately purchase either the CY8CKIT-002 MINIPROG3 or the CY8CKIT-042-BLE BLE PIONEER KIT.TM TM EZ-BLE PROC EVALUATION BOARD 1: Connect the CYBLE-012011-EVAL to the CY8CKIT-002 (MiniProg3) Connect a jumper on the J3 header Connect the MiniProg3 to the J4 10-pin header J3 Fig 2: J3 Header Fig 3: Programming/Debugging with MiniProg3 OR Plug the CYBLE-012011-EVAL on the CY8CKIT-042-BLE baseboard. Note: Jumper on CYBLE-012011-EVALs J3 header can be connected or disconnected. Fig 4: Programming and debugging with CY8CKIT-042-BLE BLE Pioneer Kit Baseboard Pin Mapping between CY8CKIT-042-BLE (Base) and CYBLE-012011-EVAL (Eval) (Base) (Eval) (Base) (Eval) (Base) (Eval) (Base) (Eval) GND GND P1 4 P1 4 P2 4 P2 4 P3 6 P3 6 VDDD, VDDDA VDD P1 5 P1 5 P2 5 P0 4 P3 7 P3 7 VDDR VDDR P1 6 P1 6 P2 6 P2 6 P4 0 P4 0 XRES XRES P1 7 P1 7 P2 7 P3 5 P5 0 P5 0 VREF VREF P2 0 P2 0 P3 2 P3 2 P5 1 P5 1 P0 6 P0 6 P2 1 P0 5 P3 3 P3 3 P0 7 P0 7 P2 2 P2 2 P3 4 P3 4 P1 0 P1 0 P2 3 P2 3 P3 5 P3 5 2: Create a project using the CYBLE-012011-00/CYBLE-012012-10 MPN and program TM /debug using PSoC Creator 3.3 SP1 The EZ-BLE PRoC Module (CYBLE-012011-00) is quali ed for the Bluetooth 4.1 speci cation and is certi ed for the 2.4 GHz unlicensed frequency range in USA (FCC), Canada (IC) and Europe (CE). Visit www.cypress.com/go/support for technical support. 2015 Cypress Semiconductor Corporation. All rights reserved. All trademarks or registered trademarks referenced herein are the properties of their respective owners. 002-10100 Rev.**