CYBLE-014008-EVAL Infineon

EZ-BLE PSOC EVALUATION BOARD CYBLE-014008-EVAL The EZ-BLE PSoC Evaluation Board (CYBLE-014008-EVAL) enables you to evaluate and develop applications on the EZ-BLE PSoC Module (CYBLE-014008-00). The EZ-BLE PSoC Module is a fully-integrated, fully-certi ed, 11 mm x 11 mm x 1.8 mm, programmable, Bluetooth Smart module designed to reduce your time-to-market. For more information visit: www.cypress.com/EZ-BLEModule - The EZ-BLE Module home page. www.cypress.com/EZ-BLEEval - The EZ-BLE PSoC Evaluation Board kit page. www.cypress.com/go/AN96841 - The getting started guide. EZ-BLE PSOC Module J6 Header GND VDD J2 Header (Bottom Side) P3 6 P3 7 P0 5 P0 4 P3 4 P3 5 P1 0 VREF P3 2 P3 3 P1 2 P1 1 P3 0 P3 1 J1 Header P0 6 P1 4 (Bottom Side) P0 7 P1 3 XRES P1 5 P2 6 P3 5 GND P2 4 P2 5 VDD P2 2 P2 3 P0 1 P2 1 VDDR GND J5 Header J4 MiniProg3 10-Pin VDDA Programming Header VDD J3 Header VDDR VDD Fig 1: CYBLE-014008-00-EVAL Pinout Description Note: To use the CYBLE-014008-EVAL you must separately purchase either the CY8CKIT-002 MINIPROG3 or the CY8CKIT-042-BLE BLE PIONEER KIT.TM EZ-BLE PSOC EVALUATION BOARD 1: Connect the CYBLE-014008-00-EVAL to the CY8CKIT-002 (MiniProg3) Connect a jumper on the J3 and Connect the MiniProg3 to the J4 10-pin header J5 headers J3 J4 J5 Fig 2: J3 and J5 Headers Fig 3: Programming/Debugging with MiniProg3 OR Plug the CYBLE-014008-EVAL on the CY8CKIT-042-BLE baseboard. Note: Jumpers on CYBLE-014008-EVALs J3 or J5 headers can be connected or disconnected. Fig 4: Programming and debugging with CY8CKIT-042-BLE BLE Pioneer Kit Baseboard Pin Mapping between CY8CKIT-042-BLE (Base) and CYBLE-014008-00 EVAL (Eval) (Base) (Eval) (Base) (Eval) (Base) (Eval) (Base) (Eval) GND GND P0 7 P0 7 P2 1 P2 1 P3 1 P3 1 VDD P1 0 P1 0 P2 2 P2 2 P3 2 P3 2 VDDD, VDDA VDDR VDDR P1 1 P1 1 P2 3 P2 3 P3 3 P3 3 XRES XRES P1 2 P1 2 P2 4 P2 4 P3 4 P3 4 1 1 P1 3 VREF VREF P1 3 P2 5 P2 5 P3 5 P3 5 P1 4 P3 6 P0 4 P0 4 P1 4 P2 6 P2 6 P3 6 1 1 P0 5 P0 5 P1 5 P1 5 P2 7 P3 5 P3 7 P3 7 P0 6 P0 6 P2 0 P0 1 P3 0 P3 0 1 The J6 header provides exibility to route P3 5 of the EZ-BLE Module to the P2 7 and/or P3 5 connections of the Pioneer Baseboard. 2: Create a project using the CYBLE-014008-00 MPN and program/debug using PSoC Creator 3.3 The EZ-BLE PSoC Module is quali ed for the Bluetooth 4.1 speci cation and is certi ed for the 2.4 GHz unlicensed frequency range in USA (FCC), Canada (IC), Europe (CE), Japan (TELEC) and Korea (KC). Visit www.cypress.com/go/support for technical support 2015-2017 Cypress Semiconductor Corporation. All rights reserved. All trademarks or registered trademarks referenced herein are the properties of their respective owners. 002-03253 Rev.*C