S25FL116K/S25FL132K/S25FL164K 16-Mbit (2 Mbyte)/32-Mbit (4 Mbyte)/ 64-Mbit (8 Mbyte), 3.0 V, SPI Flash Memory This product family has been retired and is not recommended for designs. For new and current designs, S25FL064L supersede the S25FL1-K family. These are the factory-recommended migration paths. Please refer to the S25FL-L Family datasheets for specifications and ordering information. Features Serial Peripheral Interface (SPI) with Multi-I/O Nonvolatile Status Register bits control protection modes Software command protection SPI Clock polarity and phase modes 0 and 3 Hardware input signal protection Command subset and footprint compatible with S25FL-K Read Lock-Down until power cycle protection OTP protection of security registers Normal Read (Serial): 50 MHz clock rate ( 40 C to +85 C/105 C) 90 nm Floating Gate Technology Fast Read (Serial): Single Supply Voltage 108 MHz clock rate ( 40 C to +85 C/105 C) 2.7 V to 3.6 V (Industrial, Industrial Plus, and Extended tem- Dual Read: perature range) 108 MHz clock rate ( 40 C to +85 C/105 C) 2.6 V to 3.6 V (Extended temperature range) Temperature Ranges Quad Read: 108 MHz clock rate (40 C to +85 C/105 C) Industrial ( 40 C to +85 C) 54 MB/s maximum continuous data transfer rate Industrial Plus ( 40 C to +105 C) (40 C to +85 C/105 C) Automotive, AEC-Q100 Grade 3 (40C to +85C) Efficient Execute-In-Place (XIP) Automotive, AEC-Q100 Grade 2 (40C to +105C) Continuous and wrapped read modes Package Options Serial Flash Discoverable Parameters (SFDP) S25FL116K Program 8-lead SOIC (150 mil) SOA008 Serial-input Page Program (up to 256 bytes) 8-lead SOIC (208 mil) SOC008 Program Suspend and Resume 8-contact WSON 5 mm x 6 mm WND008 Erase 24-ball BGA 6 mm 8 mm FAB024 and FAC024 Uniform sector erase (4 kB) KGD / KGW Uniform block erase (64 kB) S25FL132K Chip erase 8-lead SOIC (150 mil) SOA008 Erase Suspend and Resume 8-lead SOIC (208 mil) SOC008 Cycling Endurance 8-contact USON 4 mm 4 mm UNF008 100K Program-Erase cycles, minimum 8-contact WSON 5 mm 6 mm WND008 Data Retention 24-ball BGA 6 mm 8 mm FAB024 and FAC024 20-year data retention, minimum KGD / KGW Security S25FL164K Three 256-byte Security Registers with OTP protection 8-lead SOIC (208 mil) SOC008 Low supply voltage protection of the entire memory 16-lead SOIC (300 mil) SO3016 Pointer-based security protection feature (S25FL132K and 8-contact WSON 5 mm 6 mm WND008 S25FL164K) 24-ball BGA 6 mm 8 mm FAB024 and FAC024 Top / Bottom relative Block Protection Range, 4 kB to all of memory 8-Byte Unique ID for each device Cypress Semiconductor Corporation 198 Champion Court San Jose, CA 95134-1709 408-943-2600 Document Number: 002-00497 Rev. *I Revised July 04, 2018 Not Recommended for New DesignS25FL116K/S25FL132K/S25FL164K Logic Block Diagram CS SCK Memory SI/IO0 SO/IO1 Control Y Decoders I/O Logic Data Latch WP /IO2 HOLD /IO3 Data Path Performance Summary Maximum Read Rates (V = 2.7 V to 3.6 V, 85 C/105 C) CC Command Clock Rate (MHz) Mbytes/s Read 50 6.25 Fast Read 108 13.5 Dual Read 108 27 Quad Read 108 54 Typical Program and Erase Rates (V = 2.7 V to 3.6 V, 85 C/105 C) CC Operation kbytes/s Page Programming (256-byte page buffer) 365 4-kbyte Sector Erase 81 64-kbyte Sector Erase 131 Typical Current Consumption (V = 2.7 V to 3.6 V, 85 C/105 C) CC Operation Current (mA) Serial Read 50 MHz 7 Serial Read 108 MHz 12 Dual Read 108 MHz 14 Quad Read 108 MHz 16 Program 20 Erase 20 Standby 0.015 Deep-Power Down 0.002 Document Number: 002-00497 Rev. *I Page 2 of 90 Not Recommended for New Design X Decoders