MADL-011012 360 W CW Power Limiter Rev. V1 0.3 - 1.0 GHz Features Functional Schematic 55.6 dBm CW Power Handling +25C 54 dBm CW Power Handling +85C 0.2 dB Insertion Loss (400 - 500 MHz) 25 dB Return Loss (400 - 500 MHz) 21 dBm Flat Leakage Power 3 Lead-Free 10.1 x 6.2 x 3.2 mm Package RoHS* Compliant 1 2 RF RF IN 1 OUT Hermetic Seal Description The MADL-011012 is a lead-free surface mount, 3 GND high power limiter which integrates the equivalent of 20 PIN, Schottky, limiter diodes, capacitors, Top view inductors, and resistors in a compact ceramic package. This device provides superior low and high signal performance from 0.3 - 1.0 GHz without DC Pin Configuration bias. Pin No. Pin Name Description The MADL-011012 is ideally suitable for higher peak and CW power receiver-protector microwave circuits 1 RF RF Input IN applications where higher performance surface mount limiter assemblies are required. 2 RF RF Output OUT 2 3 Paddle Ground Ordering Information 2. The exposed paddle centered on the package bottom must be connected to RF, DC, and thermal ground. Part Number Package MADL-011012-001 bulk MADL-011012-001SMB Sample Test Board -8 1. Hermetic Seal provides fine leak rate < 5x10 atmcc/s. * Restrictions on Hazardous Substances, European Union Directive 2011/65/EU. 11 1 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: MADL-011012 360 W CW Power Limiter Rev. V1 0.3 - 1.0 GHz Electrical Specifications: T = +25C, Z = 50 (unless otherwise defined) A 0 Parameter Test Conditions Units Min. Typ. Max. -10 dBm, 300 MHz 0.25 Insertion Loss -10 dBm, 500 MHz dB 0.20 0.35 -10 dBm, 1000 MHz 0.55 10 dBm, 300 MHz 20 Return Loss -10 dBm, 500 MHz dB 25 -10 dBm, 1000 MHz 11 P1dB Input Compression Power 500 MHz dBm 13 3 CW Incident Power 500 MHz dBm 55.6 3 Peak Incident Power 1 ms pulse, 10% duty cycle, 500 MHz dBm 55.6 Flat Leakage Power 1 ms pulse, 10% duty cycle, 500 MHz dBm 20 +55.6 dBm, 1 ms pulse, 10% duty cycle, Spike Leakage Power dBm 29 500 MHz +55.6 dBm, 1 ms pulse, 10% duty cycle, Spike Leakage Energy ergs 0.5 500 MHz Recovery Time +55.6 dBm, 1 ms pulse, 10% duty cycle, s 3 (3 dB of Insertion Loss) 500 MHz Input 3rd Order Intermodulation (IIP3) -10 dBm, F1 = 500 MHz, F2 = 510 MHz dBm 29 3. Incident power ratings defined with 1.2:1 source VSWR and 1.2:1 maximum load VSWR. 4,5 Absolute Maximum Ratings Typical Performance Curve Pulse Width vs. Peak Input Power +85C Parameter Absolute Maximum (10% Duty Cycle, 500 MHz) Peak Incident Power 55.6 dBm 6 2 ms pulse, 10% duty +85C 5 CW Incident Power +85C 54 dBm 4 6 Junction Temperature 175C 3 Operating Temperature -65C to +125C 2 Storage Temperature -65C to +150C 1 4. Exceeding any one or combination of these limits may cause permanent damage to this device. 0 5. MACOM does not recommend sustained operation near these 54 55 56 57 survivability limits. Peak Incident Power (dBm) 6. Operating at nominal conditions with T +175C will ensure J 6 MTTF > 1 x 10 hours. 22 2 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: