MADL-011014 320 W Peak Power Limiter Rev. V4 1 - 2 GHz Features Functional Schematic +55 dBm Peak Power Handling +85C +53 dBm CW Power Handling +85C 0.35 dB Insertion Loss (1.2 - 1.4 GHz) 19 dB Return Loss (1.2 - 1.4 GHz) +19 dBm Flat Leakage Power 3 Lead-Free 10.1 x 6.2 x 3.2 mm Package o RoHS* Compliant and 260 C Reflow Compatible 1 2 RF RF IN OUT Hermetic Seal Description 3 GND The MADL-011014 is a lead-free surface mount, high power limiter which integrates the equivalent of Top view 19 PIN, Schottky, limiter diodes, capacitors, inductors, and resistors in a compact ceramic package. This device provides superior low and high Pin Configuration signal performance from 1 - 2 GHz without DC bias. Pin No. Pin Name Description The MADL-011014 is ideally suitable for higher peak and CW power receiver-protector microwave circuits 1 RF RF Input IN applications where higher performance surface mount limiter assemblies are required. 2 RF RF Output OUT 2 3 Paddle Ground 2. The exposed paddle centered on the package bottom must be connected to RF, DC, and thermal ground. Ordering Information Part Number Package 1 MADL-011014-001000 Hermetic Seal Sample board MADL-011014-001SMB (Hermetic Seal Limiter) -8 1. Hermetic Seal provides fine leak rate < 5x10 atmcc/s. * Restrictions on Hazardous Substances, European Union Directive 2011/65/EU. 11 1 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: MADL-011014 320 W Peak Power Limiter Rev. V4 1 - 2 GHz Electrical Specifications: T = +25C, Z = 50 (unless otherwise defined) A 0 Parameter Test Conditions Units Min. Typ. Max. -10 dBm, 1.2 - 1.4 GHz 0.35 0.6 Insertion Loss dB -10 dBm, 1.0 - 2.0 GHz 0.8 -10 dBm, 1.2 - 1.4 GHz 19 Return Loss dB -10 dBm, 1.0 - 2.0 GHz 10 P1dB Input Compression Power 1.3 GHz dBm +12 3 C.W. Incident Power 1.3 GHz dBm 55 3 Peak Incident Power 3 ms pulse, 10% duty cycle, 1.3 GHz dBm 55 Flat Leakage Power 3 ms pulse, 10% duty cycle, 1.3 GHz dBm 19 +55 dBm, 3 ms pulse, 10% duty cycle, Spike Leakage Power dBm 28 1.3 GHz +55 dBm, 3 ms pulse, 10% duty cycle, Spike Leakage Energy ergs 0.5 1.3 GHz Recovery Time +55 dBm, 3 ms pulse, 10% duty cycle, s 3.5 (3 dB of Insertion Loss) 1.3 GHz Input 3rd Order -10 dBm, F1 = 1.500 GHz, F2 = 1.510 GHz dBm 20 Intermodulation Products (IIP3) 3. Incident power ratings defined with 1.2:1 source VSWR and 1.2:1 maximum load VSWR. 4,5 Absolute Maximum Ratings Typical Performance Curve Pulse Width vs. Peak Input Power +85C Parameter Absolute Maximum (10% Duty Cycle, 1.3 GHz) Peak Incident Power 6 +55 dBm 3 ms pulse, 10% duty +85C 5 CW Incident Power +85C +53 dBm 4 6 Junction Temperature 175C 3 Operating Temperature -65C to +125C 2 Storage Temperature -65C to +150C 1 4. Exceeding any one or combination of these limits may cause permanent damage to this device. 0 5. MACOM does not recommend sustained operation near these 53 54 55 56 57 58 59 60 survivability limits. Peak Incident Power (dBm) 6. Operating at nominal conditions with T +175C will ensure J 6 MTTF > 1 x 10 hours. 22 2 M/A-COM Technology Solutions Inc. (MACOM) and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. Visit www.macom.com for additional data sheets and product information. For further information and support please visit: