MASW-009276-000D3K MACOM

MASW-009276-000DIE Bumped GaAs SP3T Switch for WLAN Rev. V1 1.0 - 4.0 GHz Features Die Bump Pad Layout (bump side up) 802.11b/g and Bluetooth Applications Low Insertion Loss: 0.5 dB 2.4 GHz to 2.5 GHz band High Isolation: 32 dB Typical on R X Low Harmonics: <-70 dBc 20 dBm Flip-chip configuration RoHS* Compliant Description MA-COMs MASW-009276-000DIE is a bumped GaAs PHEMT MMIC SP3T switch. Typical applications are WLAN (802.11 b/g) and Bluetooth applications. The MASW-009276-000DIE delivers high isolation, low insertion loss, and high linearity at 2.4 - 2.5 GHz. This device is fabricated using a Die Bump Pad Configuration 0.5 micron gate length GaAs pHEMT process. Name Description The process features full passivation for performance and reliability. This die features V 1 Voltage Control 1 C SnAg (2.5%) solder bumps for Wafer Level Chip BT Blue Tooth T /R Port X X Scale Package (WLCSP) applications. GND Ground R 2.5 GHz R Port X X Ordering Information 3 V Voltage Control 3 C Part Number Package T 2.5 GHz T Port X X MASW-009276-000D3K Die in 3000 piece reel V 2 Voltage Control 2 C MASW-009276-001SMB Sample Board SP3T RFC Antenna Port 1,2 Absolute Maximum Ratings Parameter Absolute Maximum Input Power 3 V Control +32 dBm Input Power 5 V Control +35 dBm Operating Voltage +8 volts Operating Temperature -40C to +85C Storage Temperature -65C to +150C 1. Exceeding any one or combination of these limits may cause permanent damage to this device. 2. M/A-COM does not recommend sustained operation near these survivability limits. * Restrictions on Hazardous Substances, European Union Directive 2002/95/EC. 1 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions North America Tel: 800.366.2266 / Fax: 978.366.2266 is considering for development. Performance is based on target specifications, simulated results, Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300 and/or prototype measurements. Commitment to develop is not guaranteed. Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298 PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Visit www.macomtech.com for additional data sheets and product information. Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MASW-009276-000DIE Bumped GaAs SP3T Switch for WLAN Rev. V1 1.0 - 4.0 GHz 3 Electrical Specifications : T = 25C, Z = 50 , Vc = 0 V / 3 V, Pin = 0 dBm A 0 Parameter Test Conditions Units Min. Typ. Max. Insertion Loss RFC to Tx/Rx/BT, 2.4 GHz dB 0.5 0.75 RFC to Tx, 2.4 GHz dB 20 24 Isolation RFC to Rx, 2.4 GHz dB 30 32 RFC to BT, 2.4 GHz dB 20 24 Return Loss 2.4 - 2.5 GHz dB 15 IP3 RFC to Tx/Rx/BT, 2.4 GHz, 20 dBm Total Power, 1MHz Spacing dBm 55 RFC to Tx, 2.4 GHz 32 Input P1dB RFC to Rx, 2.4 GHz dBm 28 RFC to BT, 2.4 GHz 32 Harmonics RFC to Tx 2.4 GHz, 20 dBm dBm -75 Control Current Vc = 3 V A <1 2 3. External blocking capacitors on all RF ports. 4,5,6 Recommended PCB Configuration Truth Table V 1 V 2 V 3 RFCBT RFC-T RFC-R C C C X X 1 0 0 On Off Off 0 1 0 Off On Off 0 0 1 Off Off On 4. For positive voltage control, external DC blocking capacitors are required on all RF ports. 5. Differential voltage, V(state 1) - V(state 0), must be +2.7 V minimum and must not exceed +5 V. 6. 0 = 0 0.3 V, 1 = +2.7 V to +5 V. Handling Procedures Please observe the following precautions to avoid damage: Parts List Static Sensitivity Part Value Case Style Gallium Arsenide Integrated Circuits are sensitive to electrostatic discharge (ESD) and can be C1 - C4 39 pF 0402 damaged by static electricity. Proper ESD control techniques should be used when handling these C5 - C7 1000 pF 0402 devices. 2 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions North America Tel: 800.366.2266 / Fax: 978.366.2266 is considering for development. Performance is based on target specifications, simulated results, Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300 and/or prototype measurements. Commitment to develop is not guaranteed. Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298 PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Visit www.macomtech.com for additional data sheets and product information. Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice.