24LC024-E/MS Microchip

24AA024/24LC024/24AA025/24LC025 2 2K I C Serial EEPROM Device Selection Table Description: Part VCC Max Temp. Write The Microchip Technology Inc. 24AA024/24LC024/ Number Range Clock Range Protect 24AA025/24LC025 is a 2 Kbit Serial Electrically (1) Erasable PROM with a voltage range of 1.7V to 5.5V. IYes 24AA024 1.7V-5.5V 400 kHz The device is organized as a single block of 256 x 8-bit (1) INo 24AA025 1.7V-5.5V 400 kHz memory with a 2-wire serial interface. Low current 24LC024 2.5V-5.5V 400 kHz I Yes design permits operation with typical standby and 24LC025 2.5V-5.5V 400 kHz I No active currents of only 1 A and 1 mA, respectively. The device has a page write capability for up to 16 Note 1: 100 kHz for VCC < 2.5V bytes of data. Functional address lines allow the connection of up to eight 24AA024/24LC024/ Features: 24AA025/24LC025 devices on the same bus for up to 16K bits of contiguous EEPROM memory. The device Single supply with operation from 1.7V to 5.5V for is available in the standard 8-pin PDIP, 8-pin SOIC 24AA024/24AA025 devices, 2.5V for 24LC024/ (3.90 mm), TSSOP, 2x3 DFN and TDFN and MSOP 24LC025 devices packages. Low-power CMOS technology: Package Types - Read current 1 mA, typical - Standby current 1 A, typical SOIC, TSSOP PDIP, MSOP 2 2-wire serial interface, I C compatible A0 1 8 VCC A0 1 8 VCC Cascadable up to eight devices A1 2 7 WP 2 7 A1 WP Schmitt Trigger inputs for noise suppression Output slope control to eliminate ground bounce A2 3 6 SCL 3 6 A2 SCL 100 kHz and 400 kHz clock compatibility 4 5 VSS 4 5 SDAVSS SDA Page write time 5 ms maximum DFN/TDFN Self-timed erase/write cycle 16-byte page write buffer A0 1 8 VCC 7 WP A1 2 Hardware write-protect on 24XX024 devices SCL 6 A2 3 ESD protection >4,000V VSS 5 4 SDA More than 1 million erase/write cycles Data retention >200 years Note: WP pin is not internally connected on the 24XX025. Factory programming available Packages include 8-lead PDIP, SOIC, TSSOP, Block Diagram DFN, TDFN and MSOP A0 A1 A2 WP* Pb-free and RoHS compliant HV Generator Temperature ranges: - Industrial (I): -40C to +85C I/O Memory Control Control EEPROM Logic Logic XDEC Array SDA SCL Write-Protect VCC Circuitry YDEC VSS Sense Amp. R/W Control 2008 Microchip Technology Inc. DS21210L-page 124AA024/24LC024/24AA025/24LC025 1.0 ELECTRICAL CHARACTERISTICS () Absolute Maximum Ratings VCC.............................................................................................................................................................................6.5V SS ......................................................................................................... -0.6V to VCC +1.0V All inputs and outputs w.r.t. V Storage temperature ...............................................................................................................................-65C to +150C Ambient temperature with power applied................................................................................................-40C to +125C ESD protection on all pins ................ 4 kV NOTICE: Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. TABLE 1-1: DC CHARACTERISTICS All parameters apply across the VCC = 1.7V to 5.5V specified operating ranges unless Industrial (I): TA = -40C to +85C otherwise noted. Parameter Symbol Min. Max. Units Conditions SCL and SDA pins: High-level input voltage VIH 0.7 VCC V Low-level input voltage VIL 0.3 VCC V Hysteresis of Schmitt Trigger inputs VHYS 0.05 VCC V (Note) Low-level output voltage VOL 0.40 V IOL = 3.0 mA, VCC = 4.5V IOL = 2.1 mA, VCC = 2.5V Input leakage current ILI 1 AVIN = VSS or VCC Output leakage current ILO 1 AVOUT = VSS or VCC Pin capacitance (all inputs/outputs) CIN, COUT 10 pFVCC = 5.0V (Note) TA = 25C, FCLK = 1 MHz Operating current ICC Read 1 mA VCC = 5.5V, SCL = 400 kHz ICC Write 3 mA VCC = 5.5V Standby current ICCS 1 AVCC = 5.5V, SDA = SCL = VCC WP = VSS, A0, A1, A2 = VSS Note: This parameter is periodically sampled and not 100% tested. DS21210L-page 2 2008 Microchip Technology Inc.