FlashPro5 Device Programmer Quickstart Card This quickstart card applies only to the FlashPro5 device programmer. Kit Contents Quantity Description 1 FlashPro5 programmer standalone unit 1 USB A to mini-B USB cable 1 FlashPro5 10-pin ribbon cable Software Installation FlashPro or FlashPro Express software is automatically installed as part of the Libero System-on-Chip (SoC) software. If you are using the FlashPro5 device programmer for standalone programming or on a dedicated machine, download and install the latest release of the FlashPro or FlashPro Express from the Microsemi website. The installation will guide you through the setup. Complete the software installation before connecting the FlashPro5 device programmer to your PC. Note: The minimum version requirements to run FlashPro5 on Windows are Libero SoC v11.3/ FlashPro v11.3 and on Linux are Libero SoC v 11.4/ FlashPro v11.4: www.microsemi.com/products/fpga-soc/design-resources/programming/flashpro Hardware Installation After installing the software successfully, connect one end of the USB cable to the FlashPro5 device programmer and the other end to your PCs USB port. The Found Hardware Wizard will open twice. Use the wizard to install the driver automatically (recommended). If the Found Hardware Wizard cannot find the drivers automatically, then ensure you have properly installed the FlashPro software prior to installing the hardware. If the drivers still cannot be installed automatically, then install them from a list or specific location (advanced). If FlashPro was installed as part of the Libero SoC default installation, the drivers are located at C:/Libero/Designer/Drivers/Manual. For a standalone Libero SoC FlashPro default installation, the drivers are located at C:/Microsemi/FlashPro <ver>/Drivers/. Microsemi recommends the automatic driver installation. Note: FlashPro5 uses pin 4 of the JTAG connector whereas FlashPro3 had no connection to this pin. FlashPro5 pin 4 of the JTAG header is a PROG MODE output drive signal. PROG MODE toggles between programming and normal operation. The PROG MODE signal is intended to drive an N or P Channel MOSFET to control the output of a voltage regulator between the programming voltage of 1.5 V and normal operation voltage of 1.2 V. This is required for ProASIC 3L, IGLOO V2, and IGLOO PLUS V2 devices because, although they can operate at 1.2 V, they must be programmed with a VCC core voltage of 1.5 V. Figure 1 Pin Assignments Pin 4 on FlashPro5 programmers MUST NOT be connected or used for anything other than its intended purpose. July 2014 1 2014 Microsemi CorporationCommon Issues If the On LED does not light up after FlashPro5 driver installation, the driver might not be installed correctly and you must troubleshoot the installation. For more information, refer to the FlashPro Software and Hardware Installation Guide and the Known Issues and Workarounds section of the FlashPro software release notes: www.microsemi.com/products/fpga-soc/design-resources/programming/flashpro. FlashPro5 may not operate correctly if pin 4 of the JTAG connector is improperly used. Documentation Resources Refer to the FlashPro software page for further information: www.microsemi.com/products/fpga-soc/design-resources/programming/flashpro Technical Support and Contacts Technical support is available online and by email.To find your local representative visit Microsemi SoC Sales offices, including Representatives and Distributors which are located worldwide. CE (European Conformance) This product complies with the requirements specified in EMC Directive 2004/108/IEC and RoHS Directive 2011/65/EU. Microsemi Corporation (Nasdaq: MSCC) offers a comprehensive portfolio of semiconductor and system solutions for communications, defense & security, aerospace and industrial markets. Products include high-performance and radiation-hardened analog mixed-signal integrated circuits, FPGAs, SoCs and ASICs power management products timing and synchronization devices and precise time solutions, setting the world s standard for time voice processing devices RF solutions discrete components security technologies and scalable anti-tamper products Power-over-Ethernet ICs and midspans as well as custom design Microsemi Corporate Headquarters capabilities and services. Microsemi is headquartered in Aliso Viejo, Calif., and has One Enterprise, Aliso Viejo CA 92656 USA Within the USA: +1 (800) 713-4113 approximately 3,400 employees globally. Learn more at www.microsemi.com. Outside the USA: +1 (949) 380-6100 Sales: +1 (949) 380-6136 2014 Microsemi Corporation. All rights reserved. Microsemi and the Microsemi logo are trademarks of Fax: +1 (949) 215-4996 Microsemi Corporation. All other trademarks and service marks are the property of their respective owners. E-mail: sales.support microsemi.com 50200545-1/07.14