SY100EP32V 5V/3.3V ECL 2 Divider Features General Description Guaranteed Maximum Frequency > 4 GHz The SY100EP32V is an integrated 2 divider with differential clock inputs. 3.3V and 5V Power Supply Options Guaranteed Propagation Delay < 440 ps over The VBB pin, an internally generated voltage supply, is Temperature available to this device only. For single-ended input conditions, the unused differential input is connected to Open Input Default State VBB as a switching reference voltage. VBB may also Wide Operating Temperature Range: 40C to rebias AC-coupled inputs. When used, decouple VBB +85C and VCC via a 0.01 F capacitor and limit current Available in 8-Pin MSOP Package sourcing or sinking to 0.5 mA. When not used, VBB should be left open. Package Type The RESET pin is asynchronous and is asserted on the rising edge. Upon power-up, the internal flip-flops will attain a random state the RESET allows for the SY100EP32V synchronous use of multiple EP32 in a system. 8-Lead MSOP Under open input conditions, the CLK input and the reset input will be pulled to GND. The /CLK input will be biased at half of the supply voltage. The 100K series RESET VCC 1 8 includes internal temperature compensation circuitry. R CLK Q 2 7 2 /CLK 36 /Q VBB VEE 4 5 2019 Microchip Technology Inc. DS20006171A-page 1SY100EP32V 1.0 ELECTRICAL CHARACTERISTICS Absolute Maximum Ratings PECL Power Supply Voltage (V ) ( Note 1).............................................................................................................. +6V CC NECL Power Supply Voltage (V ) ( Note 2) .............................................................................................................. 6V EE PECL Mode Input Voltage (V ) ( Note 3) ................................................................................................................... +6V IN NECL Mode Input Voltage (V ) ( Note 4) ................................................................................................................... 6V IN Continuous Output Current (I ).......................................................................................................................... 50 mA OUT Surge Output Current (I ) ................................................................................................................................ 100 mA OUT VBB Sink/Source Current (I ) (Note 5).............................................................................................................. 0.5 mA BB Notice: Stresses above those listed under Absolute Maximum ratings may cause permanent damage to the device. Exposure to maximum rating conditions for extended periods may affect device reliability. = 0V. Note 1: V CC = 0V. 2: V EE = 0V, V V . 3: V EE IN CC = 0V, V V . 4: V CC IN EE to the limited drive capability, the VBB reference should only be used for the input of the same package 5: Due device (i.e, do not use for other devices). DC ELECTRICAL CHARACTERISTICS (Note 1) Electrical Characteristics PECL: V = 3.0V to 5.5V V = 0V T = -40C to +85C, unless otherwise stated. CC EE A Parameter Symbol Min. Typ. Max. Units Conditions 37 T = 40C A Power Supply Current I = +25C 30 37 mA T EE A = +85C 42 T A V - 1.145 V - 1.020 V - 0.895 V Output High Voltage (Note 2) V OH CC CC CC 2) V V - 1.945 V - 1.820 V - 1.695 V Output Low Voltage (Note OL CC CC CC V - 1.225 V - 0.880 V Input High Voltage V IH CC CC V - 1.945 V - 1.625 V Input Low Voltage V IL CC CC Common Mode Range V 2.0 V V IHCMR CC (Note 3) V - 1.525 V - 1.425 V - 1.325 V Output Voltage V BB CC CC CC 150 A Input High Current I IH 0.5 Input Low Current CLK = V (Min) I A V IL IN IL Input Low Current /CLK 150 Note 1: Devices are designed to meet the DC specifications shown in the above table after thermal equilibration The circuit is in a test socket or mounted on a printed circuit board and transverse has been established. airflow greater than 500 lfpm is maintained. 2: Outputs are terminated through a 50 resistor to V - 2.0V. CC 3: The CMR range is referenced to the most positive side of the differential input voltage. Normal operation is obtained if the high level falls within the specified range and the peak-to-peak voltage lies between 150 mV and 1.2V. DS20006171A-page 2 2019 Microchip Technology Inc.