63911-5270 Molex

T2 Terminator for 2.00mm (.079 ) Pitch Female Crimp Terminal T2 Terminator Tooling Specification Sheet Order No. 63911-5200 FEATURES It is ideally suited for mid-volume bench operations This terminator can be installed in the TM42 and the TM40 press or Base Unit adapter for 3BF press Quick punch removal with the push of a button for fast and easy tooling change Track adjustment capabilities in the T2 Terminators for improved control of the bell mouth size and cutoff tab length T2 Terminator has standardized tooling with the Molex FineAdjust Applicator which will reduce your inventory requirements SCOPE Products: 2.00mm (.079 ) Pitch Female Crimp Terminal, 22-28 AWG. Insulation Diameter Terminal Terminal Wire Size Strip Length IPC/WHMA-A60 (1) Terminal (2) Series No. Order No. AWG mm mm In. mm In. mm In. 22 0.34 1.65 0.065 56134-8000 1.25-1.70 .049-.067 1.60-2.00 .063-.079 24 0.20 1.45 0.057 26 0.13 1.30 0.051 56134 22 0.34 1.65 0.065 0.90-1.70 .035-.067 1.60-2.00 .063-.079 24 0.20 1.45 0.057 56134-9000 26 0.13 1.30 0.051 28 (3) - - - - - - - (1) To achieve optimum IPC-A620 Class 2 insulation crimps, use this insulation OD using UL1007 wire. (2) Overall insulation OD specification for terminal. (3) 28 AWG wire is not recommenced for use in this terminal, use 22-26 AWG wire for better crimp quality. DEFINITION OF TERMS BEND UP BELL MOUTH BRUSH SEAM INSULATION CRIMP ROLLING TWISTING STRIP BEND LENGTH DOWN CONDUCTOR CUT-OFF TAB CRIMP COND.CRIMP HEIGHT The above terminal drawing is a generic terminal representation. It is not an image of a terminal listed in the scope. Doc No: ATS-639115200 Release Date: 05-05-09 UNCONTROLLED COPY Page 1 of 6 Revision: A Revision Date: 05-05-09 T2 Terminator for 2.00mm (.079 ) Pitch Female Crimp Terminal CRIMP SPECIFICATION Bell mouth Cut-off Tab Maximum Conductor Brush Terminal Series No. mm In. mm In. mm In. 56134 0.05-0.40 .002-.016 0.30 .012 0.10-0.70 .004-.028 Punch Width (Ref) Seam Bend up Bend down Twist Roll Terminal Series No. Conductor Insulation Seam shall not be Degree Degree mm In mm In open and no wire allowed out of the crimping area 56134 1.20 .047 1.50 .059 3 3 3 6 After crimping, the crimp profiles should measure the following: Conductor Insulation Pull Force Terminal Wire Size Crimp Height Crimp Width (Ref) Crimp Height Crimp Width (Ref) Minimum Order No. 2 AWG mm mm In. mm In. mm In. mm In. N Lb. 22 0.34 0.70-0.75 .028-.030 1.18-1.28 .046-.050 1.85-1.95 .073-.077 1.55-1.75 .061-.069 44.1 9.9 56134-8000 24 0.20 0.67-0.72 .026-.028 1.18-1.28 .046-.050 1.80-1.90 .071-.075 1.55-1.75 .061-.069 29.4 6.6 26 0.13 0.61-0.66 .024-.026 1.18-1.28 .046-.050 1.75-1.85 .069-.073 1.55-1.75 .061-.069 19.6 4.4 22 0.34 0.70-0.75 .028-.030 1.18-1.28 .046-.050 1.85-1.95 .073-.077 1.55-1.75 .061-.069 44.1 9.9 56134-9000 24 0.20 0.67-0.72 .026-.028 1.18-1.28 .046-.050 1.80-1.90 .071-.075 1.55-1.75 .061-.069 29.4 6.6 26 0.13 0.61-0.66 .024-.026 1.18-1.28 .046-.050 1.75-1.85 .069-.073 1.55-1.75 .061-.069 19.6 4.4 Tool Qualification Notes: 1. This Applicator was qualified to the above specifications with UL1007 wire. *An insulation diameter larger than .051 may cause the insulation grips to pierce the insulation on both sides of the insulation crimp. The customer should determine the suitability for their application. 2. Pull Force should be measured with no influence from the insulation crimp. 3. The above specifications are guidelines to an optimum crimp. Doc No: ATS-639115200 Release Date: 05-05-09 UNCONTROLLED COPY Page 2 of 6 Revision: A Revision Date: 05-05-09