AEC-Q200 RoHS Compliance This component is compliant SF2316E-3 with RoHS directive. This component was always RoHS compliant from the first date of manufacture. 1583 MHz Low-loss 1582 MHz SAW Filter Designed for 50 ohm Source/Load SAW Filter Operable Temperature Range -45/125C Absolute Maximum Ratings Rating Value Units +10 Input Power Level dBm DC Voltage on any Non-ground Terminal 3 V Operable Temperature Range -45 to +125 C Specification Temperature Range -40 to +105 C SM3030-6 Storage Temperature Range in Tape and Reel -40 to +85 C Electrical Characteristics Characteristic Sym Notes Min Typ Max Units f Center Frequency 1583 C MHz 3db Bandwidth 60 Insertion Loss, 1560 to 1606 MHz (-40 to +85C) IL 2.0 3.0 dB (-40 to +105C) 2.0 3.2 Return Loss 10 dB GD Ripple, 1560 to 1606 MHz 15.0 35.0 1573.374 to 1577.466 MHz 5.0 10.0 ns 1597.551 to 1605.886 MHz 5.0 17.0 Amplitude Ripple, 1560 to 1606 MHz (-40 to +85C) 0.9 2.0 dB (-40 to +105C) 0.9 2.5 Attenuation, 1 to 960 MHz 32 37 1427 to1501 MHz 35 45 1501 to 1525 MHz 30 37 1626 to 1660 MHz 30 43 1710 to 1785 MHz 35 40 dB 1850 to 1910 MHz 35 41 1920 to 1980 MHz 35 42 2110 to 2170 MHz 35 44 2400 to 2570 MHz 40 46 2570 to 4000 MHz 18 4000 to 6000 MHz 4.5 Case Style SMD 3.0 x 3.0 mm Nominal Footprint Lid Symbolization (Y=year, WW=week, S=shift) dot=pin 1 indicator 9D, YWWS Measurement Circuit Electrical Connections Network Analyzer Connection Terminals SF2316E-3 Input 2 Output 5 Ground All Others CAUTION: Electrostatic Sensitive Device. Observe precautions for handling. 1. Unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 and measured with 50 network analyzer. 2. Unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. 3. Rejection is measured as attenuation below the minimum IL point in the passband. Rejection in final user application is dependent on PCB layout and external impedance matching design. See Application Note No. 42 for details. 4.LRI or after the part number indicateslow rate initial productio andEN or indicatesengineering prototypes 5. The design, manufacturing process, and specifications of this filter are subject to change. 6. Either Port 1 or Port 2 may be used for either input or output in the design. However, impedances and impedance matching may vary between Port 1 and Port 2, so that the filter must always be installed in one direction per the circuit design. 7. US and international patents may apply. 8. Murata, stylized Murata logo, and Murata N.A., Inc. are registered trademarks of Murata Manufacturing Co., Ltd. Copyright Murata Manufacturing Co., Inc. All rights reserved. April 2017 SF2316E-3 8/8/19 Page 1 of 6 www.murata.comFrequency Characteristics: S21 response: (span 2.6 GHz) S21 response: (span 500 MHz) Copyright Murata Manufacturing Co., Inc. All rights reserved. April 2017 SF2316E-3 8/8/19 Page 2 of 6 www.murata.com