CU16029-UW1J Noritake

5X7 Dot Character VFD Module CU16029-UW1J 2 X 16 Characters 8mm High + Cursor The module includes the Vacuum Fluorescent Display LCD Compatible Design glass, driver and micro-controller ICs with refresh RAM, Operating Temp -40C to +85C character generator and interface logic. The high speed 8 bit parallel interface is 5V CMOS Single 5V Supply with Power Save Mode compatible suitable for connection to a host CPU bus High Brightness Blue Green Display Selectable 4/8 bit M68/i80 Parallel & Serial Interface which can be set to M68 or i80 series interface by a solder link on the module. Brightness control and power down ASCII + Extended Character Font 8 User Definable Character RAM functions are provided. A full data sheet is available. 4 Level Brightness Control Function 19.0 37.0 44.0 13.1 1 1 CN1 CN3 3.5 7.48 50.6 16.15 82.7 115.0 3.5 122.0 Dimensions in mm & subject to tolerances. 10.7 Mounting holes 3.5mm dia. 8.0 1.6 ELECTRICAL SPECIFICATION CHARACTER FONT Parameter Symbol Value Condition Power Supply Voltage VCC 5.0VDC +/- 5% GND=0V Power Supply Current ICC 350mADC typ. Vcc=5V Logic High Input VIH 2.0VDC min. VCC=5V Logic Low Input VIL 0.8VDC max. VCC=5V Logic High Output VOH Vcc-0.8VDC min. IOH = -4.0mA Logic Low Output VOL 0.6VDC max. IOH =4.0mA The power on rise time should be less than 50ms.The inrush current at power on can be 2 x ICC. The Icc current is 10mA maximum while in power down mode. OPTICAL and ENVIRONMENTAL SPECIFICATIONS Parameter Value Character Size/Pitch (XxY mm) 3.85 x 8.002/5.26 x 9.81 Dot Size/Pitch (XxY mm) 0.53 x 0.89/0.83 x 1.19 2 Luminance 350 cd/m (100 fL) min. Colour of Illumination Blue-Green (Filter for more colours) Operating Temperature -40 C to +85 C Storage Temperature -50 C to +85 C Operating Humidity (non condensing) 20 to 80% RH 25 C SOFTWARE COMMANDS PIN CONNECTIONS (CN1) Instruction R/W RS D0-D7 Pin Sig Pin Sig Clear Display L L 01H 1 GND 2 VCC Cursor Return Home L L 02H-03H 3 (FNC) 4 RS Entry Mode Set L L 04H-07H 5 R/W 6 E Display ON/OFF L L 08H-0FH 7 DB0 8 DB1 JUMPER LINKS Interface Selection Cursor/Display Shift L L 10H-1FH 9 DB2 10 DB3 Interface M68/i80 If JP5 is open parallel When jumper link JP2 is Function Set L L 20H-3FH 11 DB4 12 DB5 interface is selected. If JP5 is soldered, these inputs linked, serial interface is Brightness Set L H 00H-03H 13 DB6 14 DB7 change to i80 series CPU selected. Set CG RAM Addr. L L 40H-7FH control lines. Set DD RAM Addr. L L 80H-E7H Serial Interface Con. (CN3) CONTACT Pin 5= /WR Pin 6 = /RD Read BUSY/Addr. H L 00H-FFH Pin Signal Noritake Sales Office Tel Nos Pin 3 & 6 (Fnc) Input Nagoya Japan: +81 (0)52-561-9867 Write Data to RAM L H 00H-FFH 1 Vcc This is normally open circuit. Canada: +1-416-291-2946 Read Data from RAM H H 00H-FFH 2 SI/SO If pads JP1.1 and JP1.2 are Chicago USA: +1-847-439-9020 3 GND linked. Pin 3 of CN1 & Pin 6 of Munchen (D): +49 (0)89-3214-290 CN3 = /Reset. TIMING PARAMETERS (min) 4 STB Itron UK: +44 (0)1493 601144 (E)nable Cycle Time 500ns 5 SCK Rest Europe: +49 (0)61-0520-9220 Font Selection www.noritake-itron.com (E)nable Pulse Width 230ns 6 (FNC) IfJP6 is open, Katakana font is selected. If JP6 is linked, Hold after (E)nable 10ns Subject to change without notice. International is selected. IUK Doc Ref: 43694 Iss:1 16Jan08 NORITAKE ITRON VFD MODULES 2 x 16, 8mm Dot CharacterX-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for Vacuum Fluorescent Displays - VFD category: Click to view products by Noritake manufacturer: Other Similar products are found below : M0220SD-202SDAR1-CWC GU256X64F-9900 GU140X16G-7003B GU140X32F-7003B CU20049-UW2A CU16025-UW6J CU20029- UW1J GU140X32F-7000B VFD2041 VFD2041-VPT VK162-12 VK162-12-E VK202-25 VK204-25 VK204-25-E M0216SD-162SDAR2-1 M0216SD-162SDAR8 M0220MD-202MDAR1-1 M0220MD-202MDAR1-3 CU20025-UW1J CU20045-UW5J CU20049-UW2J CU24063- Y1A CU40025-UW6J GU140X16G-7003 VK202-25-V GU256X128E-3900B M0220SD-202SDAR1-1G GP1184A01A M162MD07AA- 000 VK202-25-V-E