NXP Semiconductors Document Number: MC9S08QL8Document Number: MC9S08QL8 RevRev.. 1, 07/2018 1, 07/2018 Data Sheet: Technical Data An Energy Efficient Solution by NXP MC9S08QL8 MC9S08QL8 Series 20-Pin TSSOP 16-Pin TSSOP Case 948E Case 948F Covers: MC9S08QL8 and MC9S08QL4 Development Support Features Single-wire background debug interface 8-Bit HCS08 Central Processor Unit (CPU) Breakpoint capability to allow single breakpoint setting Up to 20 MHz CPU at 3.6 V to 1.8 V across temperature during in-circuit debugging range of 40 C to 85 C Peripherals HC08 instruction set with added BGND instruction ADC 8-channel, 12-bit resolution 2.5 s conversion Support for up to 32 interrupt/reset sources time automatic compare function 1.7 mV/C On-Chip Memory temperature sensor internal bandgap reference channel Up to 8 KB flash memory read/program/erase over full operation in stop3 fully functional from 3.6 V to 1.8 V. operating voltage and temperature ACMP Analog comparator with selectable interrupt Up to 512 bytes random-access memory (RAM) on rising, falling, or either edge of comparator output Security circuitry to prevent unauthorized access to compare option to fixed internal bandgap reference RAM and flash contents voltage output can be tied internally to TPM input Power-Saving Modes capture operation in stop3 Two very low power stop modes TPM One 1-channel timer/pulse-width modulator Peripheral clock enable register can disable clocks to (TPM) module selectable input capture, output unused modules, thereby reducing currents compare, or buffered edge- or center-aligned PWM on Low power run each channel ACMP output can be tied internally to Low power wait input capture 6 s typical wakeup time from stop3 mode MTIM 8-bit modulo timer module with optional Typical stop current of 250 nA at 3 V, 25 C prescaler Clock Source Options RTC (Real-time counter) 8-bit modulo counter with Oscillator (XOSC) Very low-power, loop-control binary or decimal based prescaler external clock source Pierce oscillator crystal or ceramic resonator range of for precise time base, time-of-day, calendar or task 31.25 kHz to 38.4 kHz or 1 MHz to 16 MHz scheduling functions free running on-chip low power Internal Clock Source (ICS) Internal clock source oscillator (1 kHz) for cyclic wakeup without external module containing a frequency-locked-loop (FLL) components runs in all MCU modes controlled by internal reference precision trimming of SCI Full duplex non-return to zero (NRZ) LIN internal reference allows 0.2% resolution and 2% master extended break generation LIN slave extended deviation over temperature and voltage supports bus break detection wakeup on active edge frequencies from 1 MHz to 10 MHz KBI 8-pin keyboard interrupt with selectable edge System Protection and level detection modes Watchdog computer operating properly (COP) reset Input/Output with option to run from dedicated 1 kHz internal clock 18 GPIOs include one input-only and one output-only source or bus clock pin. Low-voltage detection with reset or interrupt selectable Hysteresis and configurable pullup device on all input trip points pins configurable slew rate and drive strength on all Illegal opcode detection with reset output pins except PTA5. Illegal address detection with reset Package Options Flash block protection 20-pin TSSOP, 16-pin TSSOP NXP reserves the right to change the production detail specifications as may be required to permit improvements in the design of its products. 2018 NXP B.V. All rights reserved.Table of Contents 1. Ordering Information 3 4.10.2.TPM Module Timing . 20 2. MCU Block Diagram 4 4.11. Analog Comparator (ACMP) Electricals 21 3. Pin Assignments . 5 4.12. ADC Characteristics . 21 4. Electrical Characteristics . 7 4.13. Flash Specifications . 25 4.1. Introduction . 7 4.14. EMC Performance 26 4.2. Parameter Classification . 7 5. Part Identification . 27 4.3. Absolute Maximum Ratings 7 6. Package Information . 28 4.4. Thermal Characteristics . 8 6.1. Mechanical Drawings 28 4.5. ESD Protection and Latch-Up Immunity . 9 4.6. DC Characteristics 10 4.7. Supply Current Characteristics . 14 4.8. External Oscillator (XOSC) Characteristics . 15 4.9. Internal Clock Source (ICS) Characteristics . 17 4.10. AC Characteristics 19 4.10.1.Control Timing 19 Revision History To provide the most up-to-date information, the revision of our documents on the World Wide Web will be the most current. Your printed copy may be an earlier revision. To verify you have the latest information available, refer to: