Document Number: IMXRT1010IEC NXP Semiconductors Rev. 0, 09/2019 Data Sheet: Technical Data MIMXRT1011CAE4A i.MX RT1010 Crossover Processors Data Sheet for Industrial Products Package Information Plastic Package 80-Pin LQFP, 12 x 12 mm, 0.5 mm pitch Ordering Information See Table 1 on page 4 1 i.MX RT1010 introduction The i.MX RT1010 is a member of i.MX RT real-time 1. i.MX RT1010 introduction 1 1.1. Features 2 processor family based on the Arm Cortex -M7 core, 1.2. Ordering information . 4 which operates at speeds up to 400 MHz to provide high 2. Architectural overview . 6 2.1. Block diagram 6 CPU performance and best real-time response. 3. Modules list . 7 3.1. Special signal considerations . 12 The i.MX RT1010 processor has 128 KB on-chip RAM, 3.2. Recommended connections for unused analog which can be flexibly configured as TCM or interfaces . 13 4. Electrical characteristics 15 general-purpose on-chip RAM. The i.MX RT1010 4.1. Chip-level conditions 15 integrates advanced power management module with 4.2. System power and clocks 21 DCDC and LDO that reduces complexity of external 4.3. I/O parameters 27 4.4. System modules . 30 power supply and simplifies power sequencing. The 4.5. External memory interface . 34 i.MX RT1010 also provides various memory interfaces, 4.6. Audio 40 4.7. Analog . 43 including Quad SPI, and a wide range of connectivity 4.8. Communication interfaces 49 interfaces, including UART, SPI, I2C, and USB for 4.9. Timers . 54 connecting peripherals including WLAN, Bluetooth, 5. Boot mode configuration 55 5.1. Boot mode configuration pins . 55 and GPS. The i.MX RT1010 also has rich audio features, 5.2. Boot device interface allocation 55 including SPDIF and I2S audio interface. Various analog 6. Package information and contact assignments . 57 6.1. 12 x 12 mm package information 57 IP integration, including ADC, temperature sensor, and 7. Revision history . 64 etc. NXP reserves the right to change the production detail specifications as may be required to permit improvements in the design of its products.i.MX RT1010 introduction The i.MX RT1010 is specifically useful for applications, such as: Audio Industrial Motor Control Home Appliance IoT 1.1 Features The i.MX RT1010 processors are based on Arm Cortex-M7 MPCore Platform, which has the following features: Supports single Arm Cortex -M7 with: 16 KB L1 Instruction Cache 8 KB L1 Data Cache Full featured Floating Point Unit (FPU) with support of the VFPv5 architecture Support the Armv7-M Thumb instruction set, defined in the ARM v7-M architecture Integrated MPU, up to 16 individual protection regions Up to 128 KB I-TCM and D-TCM in total Up to 500 MHz frequency Cortex M7 CoreSight components integration for debug Frequency of the core, as per Table 9,Operating ranges on page 16. The SoC-level memory system consists of the following additional components: Boot ROM (64 KB) On-chip RAM (128 KB) Configurable RAM size up to 128 KB shared with CM7 TCM External memory interfaces: SPI NOR FLASH Single/Dual channel Quad SPI FLASH with XIP support and on-the-fly decryption Octal flash Timers and PWMs: Two General Programmable Timers (GPT) 4-channel generic 32-bit resolution timer for each Each support standard capture and compare operation Periodical Interrupt Timer (PIT) Generic 32-bit resolution timer Periodical interrupt generation FlexPWM Up to 4 submodules i.MX RT1010 Crossover Processors Data Sheet for Industrial Products, Rev. 0, 09/2019 2 NXP Semiconductors