NX20P3483UKAZ NXP

NX20P3483UK USB PD and Type-C high voltage sink/source combo switch with protection Rev. 2 4 March 2019 Product short data sheet 1. General description The NX20P3483UK is a product with combined multiple power switches and an LDO for USB PD application. The device includes a bidirectional high voltage power switch which supports both 20V sink and 6V source a 5V power switch for source and a 100mA LDO provides power supply for dead battery operation. The high voltage power switch has 29V DC tolerance, and is able to sink up to 5A at maximum of 20V and source up to 3.4A at maximum of 6V. When it is configured as a high voltage sink switch, the path has overvoltage protection and reverse current protection features. While it is configured as high voltage source switch, the adjustable overcurrent limit circuit is integrated. The 5V power switch has an adjustable overcurrent limit, ideal diode feature and short circuit protection. The maximum current capability is 3.4A. It supports fast role swap for USB PD3.0 application. A VBUS discharge circuit is integrated according to USB PD VBUS discharging requirement. To minimize inrush current during normal startup, turn on slew rate control has been built in for all power switches. Over temperature protection is also equipped to automatically isolate the switch terminals when the device is overheated. 2 The device is controlled through an I C-bus interface, allowing the host to configure 2 switches and program different specified parameters according to an I C register map. The NX20P3483UK is offered with WLCSP42 package: 0.4mm pitch, 2.51 x 2.91 x 0.525mm, 0.4mm pitch. 2. Features and benefits Wide supply voltage range for VBUS from 2.8V to 20V System power supply V5V from 4.0V to 5.5V Chip power supply VDD from 2.7V to 5.5V VBUS to VCHG Switch 28m (typical) ultra low ON resistance I maximum 5A continuous current SW Bidirectional operation: 20V sink switch from VBUS to VCHG with RCP and 6V source switch from VCHG to VBUS with overcurrent limit Adjustable overcurrent limit for source configuration from 400mA to 3.4A by 2 I C-bus interface V5V to VBUS switch 38m (typical) ultra low ON resistanceNX20P3483UK NXP Semiconductors USB PD and Type-C high voltage sink/source combo switch with protection I maximum 3.4A continuous current SW 2 Adjustable overcurrent limit from 400mA to 3.4A by I C-bus interface Integrated high voltage LDO with reverse voltage protection Built in slew rate control for all power switches for inrush current limit 2 2 Supports 1MHz Fast Mode Plus I C-bus interface and four different I C slave addresses by ADDR pin Safety approvals UL 62368-1, file no. 20181009- E470128 IEC 62368-1, file no. DK-77044-UL Protection circuitry Over-Temperature Protection Over-Voltage Protection Under-Voltage Lockout Reverse current protection Surge protection: IEC61000-4-5 exceeds 95 V on VBUS IEC61000-4-5 exceeds 100 V on VBUS with 4.7uF capacitor ESD protection IEC61000-4-2 contact discharge exceeds 8 kV on VBUS IEC61000-4-2 air discharge exceeds 15kV on VBUS HBM ANSI/ESDA/JEDEC JS-001 Class 2 exceeds 2 kV on all pins CDM ANSI/ESDA/JEDEC JS-002 exceeds 500V Operating ambient temperature 40C to +85C NX20P3483UK SDS All information provided in this document is subject to legal disclaimers. NXP B.V. 2019. All rights reserved. Product short data sheet Rev. 2 4 March 2019 2 of 9