MC10H116 Triple Line Receiver Description The MC10H116 is a triple differential amplifier designed for use in sensing differential signals over long lines and is a functional/pinout duplication of the MC10116, with 100% improvement in propagation www.onsemi.com delay and no increase in power supply current. For termination information see AND8020. Features 16 20 16 Propagation Delay, 1.0 ns Typical 1 1 1 Power Dissipation 85 mW Typ/Pkg (same as MECL 10K ) Improved Noise Margin 150 mV (Over Operating Voltage and PDIP16 PLCC20 SOIC16 P SUFFIX FN SUFFIX D SUFFIX Temperature Range) CASE 64808 CASE 77502 CASE 751B05 Voltage Compensated MECL 10K Compatible These Devices are Pb-Free, Halogen Free and are RoHS Compliant MARKING DIAGRAMS* 4 2 *V to be used to supply bias to the MC10H116 only and bypassed BB (when used) with 0.01 F to 0.1 F capacitor to ground (0 V). V can BB 5 3 source < 1.0 mA. 120 The MC10H116 is designed to be used in sensing differential signals 9 6 16 16 over long lines. The bias supply (V ) is made available to make the BB 10 7 device useful as a Schmitt trigger, or in other applications where a MC10H116P 10H116G stable reference voltage is necessary. AWLYYWWG 10H116G AWLYWW 12 14 Active current sources provide these receivers with excellent AWLYYWW 1 1 13 15 common mode noise rejection. If any amplifier in a package is not used, one input of that amplifier must be connected to V to prevent BB 11 V * unbalancing the current source bias network. BB The MC10H116 does not have internal input pull down resistors. This provides high impedance to the amplifier input and facilitates V = Pin 1 A = Assembly Location CC1 differential connections. V = Pin 16 CC2 WL = Wafer Lot Applications: V = Pin 8 EE Low Level Receiver Voltage Level YY = Year When input pin with Schmitt Trigger Interface WW = Work Week bubble goes positive its respective output pin with bubble goes positive. *For additional marking information, refer to Application Note AND8002/D. Figure 1. Logic Diagram ORDERING INFORMATION Device Package Shipping 1 16 V V MC10H116DG SOIC16 48 Units/Tube CC1 CC2 2 15 (Pb-Free) A C OUT OUT 3 14 MC10H116DR2G SOIC16 2500/Tape & Reel A C OUT OUT (Pb-Free) 4 13 A C IN IN MC10H116FNG PLCC20 46 Units/Tube 5 12 A C IN IN (Pb-Free) 6 11 B V OUT BB MC10H116FNR2G PLCC20 500/Tape & Reel 7 10 B B OUT IN (Pb-Free) 8 9 V B EE IN MC10H116PG PDIP16 25 Units/Tube Pin assignment is for DualinLine Package. (Pb-Free) For PLCC pin assignment, see TND309, the Pin Conversion Tables, For information on tape and reel specifications, in- page 9. cluding part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Figure 2. Dip Pin Assignment Brochure, BRD8011/D. Semiconductor Components Industries, LLC, 2016 1 Publication Order Number: August, 2016 Rev. 11 MC10H116/DMC10H116 Table 1. MAXIMUM RATINGS Symbol Characteristic Rating Unit V Power Supply (V = 0) 8.0 to 0 Vdc EE CC V Input Voltage (V = 0) 0 to V Vdc I CC EE I Output Current mA out Continuous 50 Surge 100 T Operating Temperature Range 0 to +75 C A T Storage Temperature Range C stg Plastic 55 to +150 Ceramic 55 to +165 Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. Table 2. ELECTRICAL CHARACTERISTICS (V = 5.2 V 5%) (Note 2) EE 0 25 75 Symbol Characteristic Min Max Min Max Min Max Unit I Power Supply Current 23 21 23 mA E I Input Current High 150 95 95 A inH I Input Leakage Current 1.5 1.0 1.0 A CBO V Reference Voltage 1.38 1.27 1.35 1.25 1.31 1.19 Vdc BB V High Output Voltage 1.02 0.84 0.98 0.81 0.92 0.735 Vdc OH V Low Output Voltage 1.95 1.63 1.95 1.63 1.95 1.60 Vdc OL V High Input Voltage (Note 1) 1.17 0.84 1.13 0.81 1.07 0.735 Vdc IH V Low Input Voltage (Note 1) 1.95 1.48 1.95 1.48 1.95 1.45 Vdc IL V Common Mode Range (Note 4) 2.85 to 0.8 Vdc CMR V Input Sensitivity (Note 3) 150 typ mV PP PP 1. When V is used as the reference voltage. BB 2. Each MECL 10H series circuit has been designed to meet the specifications shown in the test table, after thermal equilibrium has been established. The circuit is in a test socket or mounted on a printed circuit board and transverse air flow greater than 500 lfpm is maintained. Outputs are terminated through a 50 ohm resistor to 2.0 V. 3. Differential input not to exceed 1.0 Vdc. 4. 150 mV differential input required to obtain full logic swing on output. p p Table 3. AC CHARACTERISTICS 0 25 75 Symbol Characteristic Min Max Min Max Min Max Unit t Propagation Delay 0.4 1.3 0.4 1.3 0.45 1.45 ns pd t Rise Time 0.5 1.5 0.5 1.6 0.5 1.7 ns r t Fall Time 0.5 1.5 0.5 1.6 0.5 1.7 ns f NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. MECL is a trademark of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries. www.onsemi.com 2