Light Touch Switches/EVPBB
2.6 mm1.6 mm SMD Light Touch Switches
Type:
EVPBB
Features
External dimensions: 2.6 mm 1.6 mm, Height 0.53 mm
High operability
Equipped with an actuator (push plate)
IP67 characteristic
Recommended Applications
Operation switches for portable electronic equipment
(Mobile phone, Portable audio)
Explanation of Part Numbers
1 2 345678 9 10 11 12
& 7 1 ##
Product Code Type Height
Specifi cations
Type Snap action/Push-on type SPST
Rating 10 A 2 Vdc to 20 mA 15 Vdc (Resistive load)
Contact Resistance 500 m max.
Electrical Insulation Resistance 50 M min. (at 100 Vdc)
Dielectric Withst and ing Voltage 250 Vac for 1 minute
Bouncing 10 ms max. (ON, OFF)
Operating Force 1.6 N
Mechanical
Travel 0.11 mm
Endurance Operating Life 500000 cycles min.
IP6x (Dust resistance) Dust : Talc (Type4) 8 h
IP67( 1)
IPx7 (Water resistance) Immersion depth : 1m 30min.
Operating Temperature 40 C to +85 C
40 C to +85 C (Bulk)
Storage Temperature
20 C to +60 C (Taping)
Minimum Quantity/Packing Unit 10000 pcs. Embossed Taping (Reel Pack)
Quantity/Carton 50000 pcs.
Note: Non washable
( 1) IP67 : Switch shall not be operated during test.
Water or dust ingress shall be limited enough to prevent deleterious effect to the switch function.
However, IP67 shall be guaranteed under single product state,
then there is a possibility that IP67 performance become impaired depending on your mounting condition or usage.
So, please ask us in advance, if the switch is applied to important usage for water and dust resistant.
Design and speci cations are each subject to change without notice. Ask factory for the current technical speci cations before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
00 Sep. 2014Light Touch Switches/EVPBB
Dimensions in mm (not to scale)
EVPBB
Embossed Taping)
(
General dimension tolerance : 0.05
( )dimensions are reference dimensions.
0.530.10
(0.35)
B
A
CC
A
B
(f0.91)
(f0.7)
A B
Actuator cross section
A B
(Section C-C)
Circuit diagram
2-3.1
2-2.2
2.60.1
Without lm
3.00.1
0.1 max.
Stencil mask plan
2-3.2
2-2.1
A B
No soldering
A B
(2)
Land pattern plan
Soldering thickness t=0.080.01
= Soldering failure may occur depending on applied
solder amount, so, please consider to use
our recommended stencil and land pattern desing.
: Recommended land pattern area
: No soldering area
Any land pattern or via holes shall not be provided
at area.
If it's necessary to design land pattern orvia
holes at area,
please apply resist to them to protect their metal
part completely.
If their metal parts are not protected
completely, short circuit failure may occur,
Besides, there should be convexoconcave by
designing additional pattern, it may cause swith
tilt, inuence on solder-ability or ux intrusion after
reow soldering.
Therefore, please study any inuence of additioan
land pattern or via holes at area in advance.
Part Numbers Operating Force Height Operating Life
EVPBB2A1B000 1.6 N 0.53 mm 500000 cycles
Design and speci cations are each subject to change without notice. Ask factory for the current technical speci cations before purchase and/or use.
Should a safety concern arise regarding this product, please be sure to contact us immediately.
00 Sep. 2014
4-0.35
0.1 max.
(0.025)
2-0.75
(1.6)
1.60.1
without the lm
2-0.3
2-0.2
and remainder
2-1.3 2-1.2 of the gate