SID1183K Power Integrations

1700 V SCALE-iDriver Up to 8 A Single Channel IGBT/MOSFET Gate Driver Providing Basic Galvanic Isolation for 1700 V IGBT and MOSFET Product Highlights Description Highly Integrated, Compact Footprint The SID1183K is a single channel IGBT and MOSFET driver in an Split outputs providing up to 8 A peak drive current eSOP package. Galvanic isolation is provided by Power Integrations Integrated FluxLink technology providing galvanic isolation innovative solid insulator FluxLink technology. The up to 8 A peak between primary-side and secondary-side output drive current enables the product to drive devices up to 600 A Rail-to-rail stabilized output voltage without requiring any additional active components. For gate drive Unipolar supply voltage for secondary-side requirements that exceed the stand-alone capability of the SID1183K, Suitable for 1700 V IGBT and MOSFET switches an external booster may be added. Stable positive and negative voltages Up to 75 kHz switching frequency for gate control are provided by one unipolar isolated voltage source. Low propagation delay time 260 ns Additional features are short-circuit protection (DESAT) with Advanced Propagation delay jitter 5 ns Soft Shut Down (ASSD), undervoltage lock-out (UVLO) for primary-side -40 C to 125 C operating ambient temperature and secondary-side and rail-to-rail output with temperature and High common-mode transient immunity process compensated output impedance guarantee safe operation eSOP package with 9.5 mm creepage and clearance distances even in harsh conditions. Advanced Protection / Safety Features Controller (PWM and fault) signals are compatible with 5 V CMOS logic, Undervoltage lock-out protection for primary and secondary-side which may also be adjusted to 15 V levels by using external resistor divider. (UVLO) and fault feedback Short-circuit protection using V monitoring and fault feedback CE SAT Advanced Soft Shut Down (ASSD) Product Portfolio Full Safety and Regulatory Compliance 1 Product Peak Output Drive Current 100% production partial discharge test 100% production HIPOT compliance testing at 6 kV RMS 1 s SID1183K 8 A Basic insulation meets VDE 0884-10 Table 1. SCALE-iDriver 1700 V Portfolio. Green Package Notes: 1. Package: eSOP-R16B. Halogen free and RoHS compliant Applications General purpose and servo drives UPS, solar, welding inverters and power supplies Figure 2. eSOP-R16B Package. SCALE-iDriver VCE Primary-Side Secondary-Side Logic Logic VGXX IN VISO Fault Output SO V TOT GH V IN VCC FluxLink GL V VCC GND VEE COM PI-7949-072616 Figure 1. Typical Application Schematic. www.power.com May 2017 This Product is Covered by Patents and/or Pending Patent Applications. - + - +1700 V SCALE-iDriver VCE V DES VGXX COM SHORT-CIRCUIT BOOTSTRAP VISO DETECTION CHARGE PUMP VCC LEVEL ASSD SHIFTER GH FluxLink SO TRANSCEIVER TRANSCEIVER (BIDIRECTIONAL) (BIDIRECTIONAL) GL GND CORE LOGIC SUPPLY MONITORING AUXILIARY CORE LOGIC COM POWER SUPPLIES SUPPLY IN MONITORING VISO AUXILIARY POWER SUPPLIES VEE CONTROL VEE PI-8285-0317171 Figure 3. Functional Block Diagram. VISO Pin (Pin 14): Pin Functional Description This pin is the input for the secondary-side positive supply voltage. VCC Pin (Pin 1): COM Pin (Pin 15): This pin is the primary-side supply voltage connection. This pin provides the secondary-side reference potential. GND Pin (Pin 3-6): GL Pin (Pin 16): This pin is the connection for the primary-side ground potential. This pin is the driver output sinking current (turn-off). All primary-side voltages refer to this pin. IN Pin (Pin 7): This pin is the input for the logic command signal. SO Pin (Pin 8): This pin is the output for the logic fault signal (open drain). NC Pin (Pin 9): VCC 1 16 GL This pin must be un-connected. Minimum PCB pad size for soldering 15 COM is required. 14 VISO VEE Pin (Pin 10): 13 GH GND 3-6 Common (IGBT emitter/MOSFET source) output supply voltage. 12 VGXX VCE Pin (Pin 11): 11 VCE This pin is the desaturation monitoring voltage input connection. IN 7 10 VEE SO 8 9 NC VGXX Pin (Pin 12): This pin is the bootstrap and charge pump supply voltage source. GH Pin (Pin 13): This pin is the driver output sourcing current (turn-on) connection. PI-7648-041415 Figure 4. Pin Configuration. 2 Rev. A 05/17 www.power.com +