QPA9126 High Linearity Gain Block Product Overview The QPA9126 is a cascadable, high linearity gain block amplifier in a low-cost surface mount package. At 3.5 GHz, the amplifier provides 16 dB gain, +35.5 dBm OIP3 and 1.4 dB Noise Figure while drawing 70 mA current from a 5V supply. 8 Pad 2x2mm DFN Package The QPA9126 provides very flat gain across a broad range of frequencies with the integration of a shut-down biasing capability to allow for operation for TDD applications. The Key Features low noise figure and high linearity performance allows the 1.06.0 GHz Operational device to be used in both receiver and transmitter chains for high performance systems. The internal active bias 50 Matched RF Input and Output circuit also enables stable operation over bias and 0.3dB Gain Flatness over 400 MHz Bandwidth temperature variations and can be biased from a single 16dB Gain positive supply ranging from +3.3 to +5 volts. The amplifier +35dBm Output IP3 is internally matched using a high-performance E-pHEMT +20 dBm P1dB process and is housed in a small 2x2 mm surface-mount package. 1.4dB Noise Figure 1.8V Logic Compatible Shutdown Control The QPA9126 covers the 1 6 GHz frequency band and is targeted for wireless infrastructure or other applications requiring high linearity and/or low noise figure. Functional Block Diagram Applications 5G m-MIMO Mobile Infrastructure Repeater / DAS General Purpose Wireless TDD / FDD System Defense Communication Ordering Information Part No. Description Top View QPA9126TR7 2,500 pieces on a 7 reel (standard) QPA9126EVB-01 Evaluation Board Datasheet, Rev. B June 26, 2019 Subject to change without notice 1 of 12 www.qorvo.com QPA9126 High Gain High Linearity Driver Amplifier Absolute Maximum Ratings Recommended Operating Conditions Parameter Rating Parameter Min Typ Max Units Storage Temperature 65C to +150C Device Voltage (VDD) +3.3 +5.0 +5.25 V RF Input Power, CW, 50, T=25C 22 dBm TCASE 40 +105 C 6 Device Voltage (VDD) +7 V Tj for >10 hours MTTF +190 C Exceeding any one or a combination of the Absolute Maximum Rating Electrical specifications are measured at specified test conditions. conditions may cause permanent damage to the device. Extended Specifications are not guaranteed over all recommended operating application of Absolute Maximum Rating conditions to the device may conditions. reduce device reliability. Electrical Specifications (1) Parameter Conditions Min Typ Max Units Operational Frequency Range 1000 6000 MHz Test Frequency 3500 MHz Gain 16 dB Gain Flatness Over 400 MHz 0.3 dB Input Return Loss 9 dB Output Return Loss 12 dB Output P1dB 20 dBm Output IP3 Pout=+1dBm/tone, f=1MHz 35.5 dBm Noise Figure EVB trace loss excluded 1.4 dB Device Current, ON VPD = 0 V 68 mA Device Current, OFF 4.5 mA VPD, Logic Low 0 0.63 V V , Logic High 1.17 V V PD DD I , Control Pin Current 30 A PD Device ON or OFF Timing 50% of V to 90% or 10% RF Output 0.07 S PD Thermal Resistance, jc Junction to case 50.0 C/W Notes: 1. Test conditions unless otherwise noted: V on EVB = +5.0V, V = 0V, Temp=+25C, 50 system. DD PD Logic Table Parameter, V High Low PD Device State OFF ON Datasheet, Rev. B June 26, 2019 Subject to change without notice 2 of 12 www.qorvo.com