TQL9063 Ultra Low-Noise, Bypass LNA Product Overview The TQL9063 is a high-linearity, ultra-low noise gain block amplifier with a bypass mode functionality integrated in the product. At 1.95GHz, the amplifier typically provides 19 dB gain, +36.3 dBm OIP3, and 0.7 dB noise figure while drawing 77 mA current from a +5V supply. The component 8-pin 2x2 mm DFN Package also provides high linearity in the bypass mode with +39 dBm IIP3. Key Features The TQL9063 is internally matched using a high- 0.5 4.0 GHz Operational bandwidth performance E-pHEMT process and only requires four LNA with integrated bypass mode external components for operation from a single positive Ability to turn LNA and bypass mode OFF supply: an external RF choke and blocking/bypass Ultra low noise, 0.7 dB at 1.95GHz capacitors. This low noise amplifier contains an internal active bias to maintain high performance over temperature. 19 dB Gain at 1.95GHz +36.3 dBm Output IP3 in LNA Mode The TQL9063 covers the 0.54.0 GHz frequency band and +39 dBm Input IP3 in Bypass Mode is targeted for wireless infrastructure. The TQL9063 is Internally matched packaged in a 2x2mm DFN. Positive supply only, +3.3 to +5V 2x2 mm 8-pin DFN plastic package Functional Block Diagram Applications Base Station Receivers Pin 1 Reference Mark Tower Mount Amplifiers Repeaters GND 1 8 V FDD-LTE, TDD-LTE, WCDMA DD General Purpose Wireless 2 7 RF In RF Out V 3 6 V BYP SD N/C 4 5 N/C Backside Paddle - RF/DC GND Top View Ordering Information Part No. Description TQL9063 5004000 MHz Bypass LNA TQL9063-PCB 5004000 MHz Evaluation Board Standard T/R size = 2500 pieces on a 7 reel Data Sheet, June 5, 2017 Subject to change without notice 1 of 12 www.qorvo.com TQL9063 Ultra Low-Noise, Bypass LNA Absolute Maximum Ratings Recommended Operating Conditions Parameter Rating Parameter Min Typ Max Units Storage Temperature 65 to 150C Device Voltage (VCC) +3.3 +5.0 +5.25 V T 40 +105 C RF Input Power, CW, 50, T=+25C +22dBm CASE 6 Device Voltage (V ) +7V Tj for >10 hours MTTF +190 C DD Electrical specifications are measured at specified test conditions. Operation of this device outside the parameter ranges given Specifications are not guaranteed over all recommended operating above may cause permanent damage. conditions. Electrical Specifications Test conditions unless otherwise noted: V = +5 V, Temp.=+25C. DD Parameter Conditions Min Typ Max Units Operational Frequency Range 500 4000 MHz Test Frequency 1950 MHz Gain LNA ON, Bypass OFF 17.5 19 20.5 dB Input Return Loss LNA ON, Bypass OFF 12 dB Output Return Loss LNA ON, Bypass OFF 9.5 dB Noise Figure LNA ON, Bypass OFF 0.7 0.9 dB Output P1dB LNA ON, Bypass OFF +21.2 dBm LNA ON, Bypass OFF, Output IP3 +31 +36.3 dBm Pout=+0 dBm/tone, f=1 MHz Insertion Loss LNA OFF, Bypass ON 1.4 dB Return Loss LNA OFF, Bypass ON 18 dB LNA OFF, Bypass ON Input IP3 +39 dBm Pin=+3 dBm/tone, f=1 MHz Isolation LNA OFF, Bypass OFF 17 dB VIH 1.6 VDD V (1) Control Voltage, V , V 1 2 V 0 0.5 V IL Bypass OFF 60 77 100 mA Current, ID Bypass ON 3 mA Bypass to LNA Mode 983 ns (2) Switching Speed LNA to Bypass Mode 1.9 s LNA to OFF 200 ns Thermal Resistance, jc Channel to case 44 C/W Notes: 1. These voltages are reference at the turrets labelled V1 and V2 on the circuit schematic on page 3. 2. To achieve these fast switching speeds it is required to place a 91K shunt resistor at the RFout pin 7. Refer pg. 6. Control Truth Table V V State BYP SD 0 0 LNA ON, Bypass OFF 0 1 LNA OFF, Bypass OFF 1 x LNA OFF, Bypass ON Data Sheet, June 5, 2017 Subject to change without notice 2 of 12 www.qorvo.com