QPA9807 2300 2700 MHz 1/4W Balanced Amplifier General Description The QPA9807 is a balanced amplifier module with embedded hybrid couplers to convert to single ended input and output ports. The module has an enable pin to allow for shutting down of the amplifier. The module requires minimal external components which are VCC choke inductors, decoupling caps and resistors for bias control. 16 Pad 5x5mm leadless SMT Package The QPA9807 provides +24.7 dBm P1dB with 19.6 dB gain and +38.7 dBm OIP3 across a wide frequency range of Product Features 2300-2700 MHz to cover the 3GPP Bands 7, 30, 38, 40, and 41. The linear driver amplifier is targeted for use in 23002700 MHz wireless infrastructure where high linearity, medium power Balanced Amplifier with integrated 3 dB hybrids and high integration is required. The balanced amplifier Internally Matched 50 Input / Output configuration provides very good input and output VSWR Shutdown Mode with 1.8V logic control and is especially ideal as the output stage in a macrocell 19.6 dB Gain transceiver board that connects to the high power amplifier +38.7 dBm OIP3 (HPA) board through a long cable or microstrip trace. The QPA9807 is packaged in a small 5x 5mm leadless +24.7 dBm P1dB package that is internally matched to 50 on all RF ports. Good gain flatness across Bands 7, 30, 38, 40, 41 Functional Block Diagram Applications Wireless Infrastructure Macro BTS Transceivers Booster Amps, Repeaters Ordering Information Part No. Description QPA9807TR13 2,500 pieces on a 13 reel (standard) QPA9807EVB-01 2300 2700MHz Evaluation Board Top View Datasheet, November 4, 2020 Subject to change without notice - 1 of 10 - www.qorvo.com QPA9807 2300 2700 MHz 1/4W Balanced Amplifier Absolute Maximum Ratings Recommended Operating Conditions Parameter Rating Parameter Min Typ Max Units Storage Temperature 40 to +150C Device Voltage (VCC A&B) +3.30 +5 +5.25 V RF Input Power, CW, 50, T=25C +22 dBm Enable (High) +1.17 +1.8 +3.6 V Supply Voltage (VCC) +6 V Enable (Low) 0 +0.63 V Enable Voltage (Enable) VCC A&B + 0.5 V T 40 +105 C CASE 6 Exceeding any one or a combination of the Absolute Maximum Rating Tj for >10 hours MTTF +190 C conditions may cause permanent damage to the device. Extended Electrical specifications are measured at specified test conditions. application of Absolute Maximum Rating conditions to the device may Specifications are not guaranteed over all recommended operating reduce device reliability. conditions. Electrical Specifications (1) Parameter Conditions Min Typ Max Units Operational Frequency Range 2300 2700 MHz Test Frequency 2500 MHz Gain 18.5 19.6 21.5 dB dB Fc 100 MHz 0.1 dB Fc 250 MHz 0.3 Gain Slope (peak to peak) dB Fc 350 MHz 0.4 Fc 500 MHz 0.5 dB Output IP3 Pout =+7 dBm/tone, f =1 MHz +35.5 +38.7 dBm Output P1dB +24.0 +25.0 dBm Noise Figure 1.4 dB Input Return Loss dB 27 Output Return Loss dB 28 Control Current I (Pin 6) 3 mA VCC CTRL1 Total Current I (Pin 8) and I (Pin 13) 340 mA VCC A VCC B 286 Enable Time 50% Enable to 90% RF 220 ns Disable Time 50% Enable to 10% RF 60 ns Thermal Resistance, jc Module (junction to backside ground paddle) 28.4 C/W Notes: 1. Test conditions unless otherwise noted: VCC A&B=VCC CTRL1 = +5.0V, Enable = +1.8V, Temp=+25C, 50 system. Logic Table Parameter High Low Enable Active Shutdown Datasheet, November 4, 2020 Subject to change without notice - 2 of 10 - www.qorvo.com