QPC6614TR13 Qorvo

QPC6614 5MHz to 6000MHz Digital Step Attenuator Product Description The QPC6614 is a 6-bit digital step attenuator (DSA) that features high linearity over the entire 31.5 dB gain control range with 0.5 dB steps. The QPC6614 uses serial control interface. The QPC6614 has a low insertion loss of 1.4 dB 24-pin 4.2mmx4.2mmx0.975mm at 2 GHz. Patented circuit architecture provides overshoot-free transient switching performance. Key Features 6-Bit, 31.5 dB, 0.5dB Step Patented Circuit Architecture Overshoot-free During Attenuation State Transitions Frequency Range 5MHz to 6000MHz High Linearity, IIP3 +55dBm Typical Serial Control Interface Functional Block Diagram Fast Switching, 120 ns Typical Single Supply 3V to 5V Operation No DC Voltage on RF Pins, DC Grounding Allowed Externally Power-up Attenuation State Programmable Applications 2G through 4G Base Stations Point-to-Point Wi-Fi Test Equipment Top View Ordering Information Part No. Description QPC6614TR13 2500 pcs on 13 reel QPC6614PCK401 5-600MHz PCBA w/5pcs sample bag Datasheet, October 26, 2020 Subject to change without notice 1 of 16 www.qorvo.com QPC6614 5MHz to 6000MHz Digital Step Attenuator Absolute Maximum Ratings Recommended Operating Conditions Parameter Min Typ Max Units Parameter Rating (2) Storage Temperature 40 to +150C DC Supply Voltage (VDD) +2.7 +5 +5.5 V DC Supply Voltage (V ) 0.5 to +6.0 V Case Temperature, TC 40 +105 C DD Signal Level (CLK, SERIN, LE and PUP2), Operating Junction Temp. TJ +125 C 0.5 to V DD when V is applied DD Notes: 1. Electrical specifications are measured at specified test conditions. Signal Level (CLK, SERIN, LE and PUP2), -0.5 to +4.0 V Specifications are not guaranteed over all recommended operating when VDD is not applied conditions. RF Input Power (RFIN), +85C Case Temp +30dBm 2. It is recommended to apply V before applying any signal to logic DD pins. RF Input Power (RFOUT), +85C Case Temp +27dBm Notes: 1. Exceeding any one or a combination of the Absolute Maximum Rating conditions may cause permanent damage to the device. Extended application of Absolute Maximum Rating conditions to the device may reduce device reliability. Electrical Specifications Parameter Conditions Min Typ Max Units Frequency Range 5 6000 MHz Insertion Loss 0dB Attenuation Setting 1.4 2.4 dB Attenuation Range 31.5 dB Attenuation Step 0.5 dB Attenuation Accuracy (0.3 + 3% of Atten. Setting) dB Input IP3 +55 dBm Input P0.1dB +30 dBm RF Input Power to RFIN +27 dBm RF Input Power to RFOUT +20 dBm Return Loss 15 dB Switching Time 50% LE Rising Edge to 10%/90% RF Output 120 ns Successive Step Phase Delta 2000 MHz 2 Deg. (2) Supply Current, IDD Steady state operation 180 A At maximum attenuation state with RF power Thermal Resistance 60 C/W applied to the ATTIN Notes: 1. Test conditions unless otherwise noted: VDD=+5V, Temp= +25C, Freq = 2GHz, 50 system. 2. Current draw during attenuation state transitions is higher. Control Logic Specifications Parameter Conditions Min Typ Max Units Logic Low Input Voltage 0 +0.63 V Logic High Input Voltage +1.17 VDD V Notes: 1. Test conditions unless otherwise noted: V =+5V, Temp= +25C Apply to CLK, SERIN, LE and PUP2 DD Datasheet, October 26, 2020 Subject to change without notice 2 of 16 www.qorvo.com