RFFM8550QPCK-410 Qorvo

RFFM8550Q RFFM8550Q Q 5GHz WiFi Switch + LNA Module Tested in Accordance with AEC-Q100 Package: DFN, 8-pin, 1.5mm x 1.5mm x 0.50mm The RFFM8550Q provides an integrated switch + LNA solution in a Features single Front End Module (FEM) for automotive WiFi 802.11a/n/ac SP2T T/R Switch systems. The ultra-small form factor and integrated matching greatly reduces the number of external components and layout area in the LNA with Bypass Mode customer applications. This simplifies the total front end solution by Input and Output Matched to 50 reducing the bill of materials, system footprint, and manufacturing cost. Wide Voltage Supply Range The RFFM8550Q integrates a Single Pole 2-Throw (SP2T) switch and a Supports WiFi chipsets with Low Noise Amplifier (LNA) with bypass mode. The device is provided in Integrated Power Amplifier (iPA) a 1.5mm x 1.5mm x 0.50mm 8-pin DFN package. Low Profile Package for Module Designs Applications 1 TX ANT 8 Automotive WiFi VRX 2 7 N/C WiFi Direct Automotive Diagnostics VTX 3 6 RX WiFi Infotainment 5GHz ISM Band Solutions for VDD 4 5 LNAEN Automotive Functional Block Diagram Ordering Information RFFM8550QSB Standard 5-piece sample bag RFFM8550QSQ Standard 25-piece sample bag RFFM8550QSR Standard 100-piece reel RFFM8550QTR7 Standard 2500-piece reel RFFM8550QPCK-410 Fully assembled evaluation board w/ 5-piece bag Revision E 1 o f 8 Disclaimer: Subject to change without notice 2015 RF Micro Devices, Inc. www.qorvo.com RFFM8550Q Absolute Maximum Ratings Caution ESD sensitive device. Parameter Rating Unit DC Supply Voltage (No RF Applied) -0.5 to 6 V DC Supply Current 100 mA RFMD Green: RoHS status based on EU Operating Case Temperature -40 to +85 C Directive 2011/65/EU (at time of this Storage Temperature -40 to +150 C document revision), halogen free per IEC 61249-2-21, < 1000ppm each of Maximum TX Input Power for 11b/g/n/ac (No Damage) +30 dBm antimony trioxide in polymeric materials Maximum RX Input Power (No Damage) +12 dBm and red phosphorus as a flame retardant, and <2% antimony in solder. Bypass Mode Maximum RX input power (No damage) +25 dBm Exceeding any one or a combination of the Absolute Moisture Sensitivity MSL1 Maximum Rating conditions may cause permanent damage to the device. Extended application of Absolute Maximum Rating conditions to the device may reduce device reliability. Specified typical performance or functional operation of the device under Absolute Maximum Rating conditions is not implied. Nominal Operating Parameters Specification Parameter Unit Condition Min Typ Max Compliance: 802.11a / n / ac Operating Frequency 5.18 5.825 GHz Operating Temperature -40 25 85 C Power Supply V 3.0 3.6 5.0 V DD Control Voltage-high 2.8 3.1 VCC V VTX, VRX, and LNA EN Should not exceed VCC voltage Control Voltage-low 0 0.24 V Transmit (TX-ANT) Over all conditions unless otherwise noted 0.6 1.2 dB Temp = 25C V = 3.6V Control Voltage = 3.1V DD Insertion Loss 0.6 1.8 dB TX Port Return Loss 12 25 dB ANT Port Return Loss 12 25 dB Input P1dB 26 28 dBm Temp = 25C V = 3.6V Control Voltage = 3.1V CW signal DD ANT-RX Isolation 28 35 dB TX Mode Receive (ANT-RX)-LNA On Over all conditions unless otherwise noted 9 12 14 dB Temp = 25C V = 3.6V Control Voltage = 3.1V DD Gain 7 12 16 Gain flatness -0.25 +0.25 dB Over any 80MHz BW Temp =25C V =3.6V Control Voltage=3.1V DD Gain flatness across band -1 +1 dB Temp = 25C VDD = 3.6V Control Voltage = 3.1V 2.5 3 dB Noise Figure-Nominal 2.5 4.0 dB Rx Port Return Loss 8 12 dB ANT Port Return Loss 8 10 dB Input P1dB -6 -3 dBm Temp = 25C V = 3.6V Control Voltage = 3.1V DD 6 12 14 mA Current Consumption 4 12 16 mA LNAEN Control Current 140 250 A LNA Turn On Time 400 600 nS 2 of 8 Revision E Disclaimer: Subject to change without notice 2015 RF Micro Devices, Inc. www.qorvo.com