89HPES32NT8AG2 32-Lane 8-Port PCIe Gen2 Datasheet System Interconnect Switch All BARs support 32/64-bit base and limit address translation Device Overview Two BARs (BAR2 and BAR4) support look-up table based The 89HPES32NT8AG2 is a member of the IDT family of PCI address translation Express switching solutions. The PES32NT8AG2 is a 32-lane, 8-port 32 inbound and outbound doorbell registers system interconnect switch optimized for PCI Express Gen2 packet 4 inbound and outbound message registers switching in high-performance applications, supporting multiple simulta- Supports up to 64 masters neous peer-to-peer traffic flows. Target applications include multi-host or Unlimited number of outstanding transactions intelligent I/O based systems where inter-domain communication is Multicast required, such as servers, storage, communications, and embedded systems. Compliant with the PCI-SIG multicast Supports 64 multicast groups Features Supports multicast across non-transparent port High Performance Non-Blocking Switch Architecture Multicast overlay mechanism support 32-lane, 8-port PCIe switch with flexible port configuration ECRC regeneration support Integrated SerDes supports 5.0 GT/s Gen2 and 2.5 GT/s Integrated Direct Memory Access (DMA) Controllers Gen1 operation Supports up to 2 DMA upstream ports, each with 2 DMA chan- Delivers up to 32 GBps (256 Gbps) of switching capacity nels Supports 128 Bytes to 2 KB maximum payload size Supports 32-bit and 64-bit memory-to-memory transfers Low latency cut-through architecture Fly-by translation provides reduced latency and increased Supports one virtual channel and eight traffic classes performance over buffered approach Port Configurability Supports arbitrary source and destination address alignment Eight x4 switch ports Supports intra- as well as inter-partition data transfers using Adjacent x4 ports can be merged to achieve x8 port widths the non-transparent endpoint Automatic per port link width negotiation Supports DMA transfers to multicast groups (x8 x4 x2 x1) Linked list descriptor-based operation Crosslink support Flexible addressing modes Automatic lane reversal Linear addressing Per lane SerDes configuration Constant addressing De-emphasis Quality of Service (QoS) Receive equalization Port arbitration Drive strength Round robin Innovative Switch Partitioning Feature Request metering Supports up to 8 fully independent switch partitions IDT proprietary feature that balances bandwidth among Logically independent switches in the same device switch ports for maximum system throughput Configurable downstream port device numbering High performance switch core architecture Supports dynamic reconfiguration of switch partitions Combined Input Output Queued (CIOQ) switch architecture Dynamic port reconfiguration downstream, upstream, with large buffers non-transparent bridge Clocking Dynamic migration of ports between partitions Supports 100 MHz and 125 MHz reference clock frequencies Movable upstream port within and between switch partitions Flexible port clocking modes Non-Transparent Bridging (NTB) Support Common clock Supports up to 8 NT endpoints per switch, each endpoint can Non-common clock communicate with other switch partitions or external PCIe Local port clock with SSC (spread spectrum setting) and port domains or CPUs reference clock input 6 BARs per NT Endpoint Bar address translation IDT and the IDT logo are registered trademarks of Integrated Device Technology, Inc. 1 of 35 December 17, 2013 2013 Integrated Device Technology, IncIDT 89HPES32NT8AG2 Datasheet Hot-Plug and Hot Swap Standards and Compatibility Hot-plug controller on all ports PCI Express Base Specification 2.1 compliant Hot-plug supported on all downstream switch ports Implements the following optional PCI Express features 2 All ports support hot-plug using low-cost external I C I/O Advanced Error Reporting (AER) on all ports expanders End-to-End CRC (ECRC) Configurable presence-detect supports card and cable appli- Access Control Services (ACS) cations Device Serial Number Enhanced Capability GPE output pin for hot-plug event notification Sub-System ID and Sub-System Vendor ID Capability Enables SCI/SMI generation for legacy operating system Internal Error Reporting support Multicast Hot-swap capable I/O VGA and ISA enable Power Management L0s and L1 ASPM Supports D0, D3hot and D3 power management states ARI Active State Power Management (ASPM) Power Supplies Supports L0, L0s, L1, L2/L3 Ready, and L3 link states Requires three power supply voltages (1.0V, 2.5V, and 3.3V) Configurable L0s and L1 entry timers allow performance/ Packaged in a 23mm x 23mm 484-ball Flip Chip BGA with power-savings tuning 1mm ball spacing SerDes power savings Supports low swing / half-swing SerDes operation Product Description SerDes associated with unused ports are turned off With Non-Transparent Bridging functionality and innovative Switch SerDes associated with unused lanes are placed in a low Partitioning feature, the PES32NT8AG2 allows true multi-host or multi- power state processor communications in a single device. Integrated DMA control- Reliability, Availability, and Serviceability (RAS) lers enable high-performance system design by off-loading data transfer ECRC support operations across memories from the processors. Each lane is capable AER on all ports of 5 GT/s link speed in both directions and is fully compliant with PCI SECDED ECC protection on all internal RAMs Express Base Specification 2.1. End-to-end data path parity protection A non-transparent bridge (NTB) is required when two PCI Express Checksum Serial EEPROM content protected domains need to communicate to each other. The main function of the Ability to generate an interrupt (INTx or MSI) on link up/down NTB block is to initialize and translate addresses and device IDs to transitions allow data exchange across PCI Express domains. The major function- Initialization / Configuration alities of the NTB block are summarized in Table 1. Supports Root (BIOS, OS, or driver), Serial EEPROM, or SMBus switch initialization Common switch configurations are supported with pin strap- ping (no external components) Supports in-system Serial EEPROM initialization/program- ming On-Die Temperature Sensor Range of 0 to 127.5 degrees Celsius Three programmable temperature thresholds with over and under temperature threshold alarms Automatic recording of maximum high or minimum low temperature 9 General Purpose I/O Test and Debug Ability to inject AER errors simplifies in system error handling software validation On-chip link activity and status outputs available for several ports Per port link activity and status outputs available using 2 external I C I/O expander for all remaining ports Supports IEEE 1149.6 AC JTAG and IEEE 1149.1 JTAG 2 of 35 December 17, 2013