IDTF1763NBGI Datasheet RF to IF Single Downconverting Mixer 2000MHz to 2900MHz FEATURES GENERAL DESCRIPTION Ideal for Multi-Carrier Systems This document describes the specification2 for the TM Lowside or Highside LO IDTF1763 Zero-Distortion Highband RF to IF Single 11.7dB Gain Downconverting Mixer. This device is part of a series of Ultra linear +45dBm IP3 using HS LO or mixers using lowside or highside LO injection options for O +42dBm IP3 using LS LO all UTRA frequency bands. See the Part Matrix for the O 9.7 dB NF detail of all devices in this series. 200 output impedance The F1763 single channel device is designed to operate Wide flat performance IF BW with a single 5V supply. It is optimized for operation in Drives ADC directly for DPD applications a Multi-mode, Multi-carrier BaseStation Receiver for Low Power Consumption frequency bands from 2000MHz - 2900MHz using 5x5 20 pin package either lowside or highside LO. IF frequencies from Standby Mode 50MHz to 500MHz are supported. Nominally, the device offers +42 dBm Output IP3 with 200mA of ICC. COMPETITIVE ADVANTAGE DEVICE BLOCK DIAGRAM In typical basestation receivers, the RF to IF mixer dominates the linearity performance for the entire TM receive system. The Zero-Distortion family of mixers RF dramatically improve the maximum signal levels (IM IF 3 OUT tones) that the BTS can withstand at a desired Signal to TM Noise Ratio (SNR.) Zero-Distortion technology allows realization of either benefit. In basestation transmitters, STBY LO Bias digital pre-distortion (DPD) is employed to improve the Control Transmitter performance. By utilizing an ultra-linear I SET mixer in the DPD RX path, such as the IDTF1763, the ACLR and/or power consumption of the full Tx system can be improved significantly. This is because the F1763 V CC can directly drive an ADC through an Anti-Alias filter. Downstream amplification is not necessary in the DPD application. ORDERING INFORMATION IP3 : 12 dB O Omit IDT Tape & 0.8 mm height Dissipation: 10% prefix Reel package Allows for higher RF gain improving Sensitivity IDTF1763NBGI8 Eliminates the need for an ADC driver or IF VGA in DPD Green RF product Line Industrial linearization path Temp range PART MATRIX Part RF Range UTRA bands IF freq Typ. Injection range Gain FF11770011 660000 -- 11006600 55,,66,,88,,1122,,1133,,1144,,1177,,11 7700 -- 330000 1111..88 BBootthh 8,19,20, 26 8,19,20, 26 FF11775511 11440000 -- 22550000 11,,22,,33,,44,,99,,1100,,1111,, 5500 -- 550000 1111..88 BBootthh 2211,,2233,,2244,,2255,,3333,,3344,, 3355,,3366,,3377,,3399,, 4400 FF11776633 22000000 -- 22990000 77,,3388,,4400,,4411 5500 -- 550000 1111..77 BBootthh TM IDT Zero-Distortion Mixer 1 RevO December 2013 IDTF1763NBGI Datasheet RF to IF Single Downconverting Mixer 2000MHz to 2900MHz ABSOLUTE MAXIMUM RATINGS VCC to GND -0.3V to +5.5V STBY -0.3V to (VCC + 0.3V) IF OUT+, IF OUT-, RF IN -0.3V to (VCC + 0.3V) LO IN -0.3V to +0.3V IF SET to GND, IF BIAS to GND -0.3V to +1.2V RF Input Power +20dBm Continuous Power Dissipation 1.3W (Junction Ambient) +40C/W JA (Junction Case) The Case is defined as the exposed paddle +3C/W JC Operating Temperature Range (Case Temperature) T = -40C to +105C C Maximum Junction Temperature 150C Storage Temperature Range -65C to +150C Lead Temperature (soldering, 10s) +260C Stresses above those listed above may cause permanent damage to the device. Functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. TM IDT Zero-Distortion Mixer 2 RevO December 2013