HA4600 Data Sheet October 2, 2015 FN3990.10 480MHz, SOT-23, Video Buffer with Output Features Disable Micro Package Available . SOT-23 Low Power Dissipation . 105mW The HA4600 is a very wide bandwidth, unity gain buffer ideal for professional video switching, HDTV, computer monitor Symmetrical Slew Rates 1700V/s routing, and other high performance applications. The circuit 0.1dB Gain Flatness . 250MHz features very low power dissipation (105mW Enabled, 1mW Off Isolation (100MHz) . 85dB Disabled), excellent differential gain and phase, and very high off isolation. When disabled, the output is switched to a Differential Gain and Phase 0.01%/0.01 high impedance state, making the HA4600 ideal for routing High ESD Rating . >1800V matrix equipment and video multiplexers. TTL Compatible Enable Input The HA4600 also features fast switching and symmetric Improved Replacement for GB4600 slew rates. A typical application for the HA4600 is interfacing Intersils wide range of video crosspoint switches. Pb-Free (RoHS Compliant) For applications requiring a tally output (enable indicator), Applications please refer to the HA4201 data sheet. Professional Video Switching and Routing Pinouts Video Multiplexers HA4600 HDTV (PDIP- No longer available or supported) (SOIC) Computer Graphics TOP VIEW RF Switching and Routing PCM Data Routing EN 1 8 GND Ordering Information V- 2 7 IN PART TEMP. PKG V+ 3 6 NC NUMBER PART RANGE PACKAGE DWG. (Note 2) MARKING (C) (Pb-free) OUT 4 5 NC HA4600CPZ HA4600CPZ 0 to +70 8 Ld PDIP (Note 1) E8.3 (No longer HA4600 available, (SOT-23) recommended TOP VIEW replacement: HA4600CBZ or HA4600CHZ96 HA4600CBZ 4600CBZ 0 to +70 8 Ld SOIC M8.15 EN 1 6 OUT HA4600CBZ96 4600CBZ 0 to +70 8 Ld SOIC M8.15 V- 2 5 V+ Tape and Reel 3 4 GND IN HA4600CHZ96 46Z (Note 3) 0 to +70 6 Ld SOT-23 P6.064 Tape and Reel NOTES: 1. Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing Truth Table applications. EN OUT 2. Intersil Pb-free plus anneal products employ special Pb-free material sets molding compounds/die attach materials and 100% matte tin 0 High Z plate termination finish, which are RoHS compliant and compatible 1Active with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020 3. The part marking is located on the bottom of the part. CAUTION: These devices are sensitive to electrostatic discharge follow proper IC Handling Procedures. 1 1-888-INTERSIL or 1-888-468-3774 Copyright Intersil Americas LLC 2000, 2005, 2013., 2015 All Rights Reserved Intersil (and design) is a trademark owned by Intersil Corporation or one of its subsidiaries. All other trademarks mentioned are the property of their respective owners.HA4600 Absolute Maximum Ratings Thermal Information Voltage Between V+ and V- 12V Thermal Resistance (Typical, Note 1) (C/W) JA Input Voltage . V SUPPLY PDIP Package* 130 Digital Input Current (Note 2) . 25mA SOIC Package . 170 Output Current . 20mA SOT-23 Package . 210 ESD Rating Maximum Junction Temperature (Die) . 175C Human Body Model (Per MIL-STD-883 Method 3015.7) 1800V Maximum Junction Temperature (Plastic Package) . 150C Maximum Storage Temperature Range -65C to 150C Operating Conditions Maximum Lead Temperature (Soldering 10s) 300C (SOIC and SOT-23 - Lead Tips Only) Temperature Range 0C to 70C *Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications. CAUTION: Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 4. is measured with the component mounted on an evaluation PC board in free air. JA 5. If an input signal is applied before the supplies are powered up, the input current must be limited to this maximum value. Electrical Specifications V = 5V, R = 10k , V = 2.0V, Unless Otherwise Specified SUPPLY L EN PARAMETER TEST CONDITIONS TEMP. (C) MIN TYP MAX UNITS DC SUPPLY CHARACTERISTICS Supply Voltage Full 4.5 5.0 5.5 V Supply Current (V =0V) V = 2V 25, 70 - 10.5 13 mA OUT EN V = 2V 0 - - 14.5 mA EN V = 0.8V 25, 70 - 100 115 A EN V = 0.8V 0 - 100 125 A EN ANALOG DC CHARACTERISTICS Output Voltage Swing without Clipping V =V V 20mV 25, 70 2.7 2.8 - V OUT IN IO 0 2.4 2.5 - V Output Current Full 15 20 - mA Input Bias Current Full - 30 50 A Output Offset Voltage 25 -10 - 10 mV Output Offset Voltage Drift (Note 3) Full - 25 50 V/C SWITCHING CHARACTERISTICS Turn-On Time 25 - 160 - ns Turn-Off Time 25 - 320 - ns DIGITAL DC CHARACTERISTICS Input Logic High Voltage Full 2 - - V Input Logic Low Voltage Full - - 0.8 V EN Input Current 0V to 4V Full -2 - 2 A AC CHARACTERISTICS Insertion Loss 1V Full - 0.04 0.05 dB P-P FN3990.10 2 October 2, 2015