DATASHEET HA5023 FN3393 Rev 9.00 Dual 125MHz Video CurrentFeedback Amplifier September 30, 2015 The HA5023 is a wide bandwidth high slew rate dual Features amplifier optimized for video applications and gains between Wide Unity Gain Bandwidth . 125MHz 1 and 10. It is a current feedback amplifier and thus yields less bandwidth degradation at high closed loop gains than Slew Rate . 475V/s voltage feedback amplifiers. Input Offset Voltage 800V The low differential gain and phase, 0.1dB gain flatness, and Differential Gain . 0.03% ability to drive two back terminated 75 cables, make this Differential Phase . 0.03 amplifier ideal for demanding video applications. Supply Current (per Amplifier) 7.5mA The current feedback design allows the user to take advantage of the amplifiers bandwidth dependency on the ESD Protection 4000V feedback resistor. By reducing R , the bandwidth can be F Guaranteed Specifications at 5V Supplies increased to compensate for decreases at higher closed loop gains or heavy output loads. Pb-Free Plus Anneal Available (RoHS Compliant) The performance of the HA5023 is very similar to the Applications popular Intersil HA-5020 . Video Gain Block Ordering Information Video Distribution Amplifier/RGB Amplifier TEMP. Flash A/D Driver PART RANGE PKG. PART NUMBER MARKING (C) PACKAGE DWG. Current to Voltage Converter HA5023IPZ HA5023IPZ -40 to 85 8 Ld PDIP* E8.3 Medical Imaging (Note) (No (Pb-free) Radar and Imaging Systems longer available, Video Switching and Routing recommended replacement: Pinout HA5023IBZ) HA5023 HA5023IBZ 5023IBZ -40 to 85 8 Ld SOIC M8.15 (PDIP, SOIC) (Note) (Pb-free) TOP VIEW HA5023IBZ96 5023IBZ -40 to 85 8 Ld SOIC M8.15 (Note) Tape and Reel OUT1 1 8 V+ (Pb-free) -IN1 2 + 7 OUT2 - *Pb-free PDIPs can be used for through hole wave solder processing +IN1 3 6 -IN2 only. They are not intended for use in Reflow solder processing + - applications. V- 4 5 +IN2 NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020. FN3393 Rev 9.00 Page 1 of 17 September 30, 2015HA5023 Absolute Maximum Ratings Thermal Information Voltage Between V+ and V- Terminals .36V Thermal Resistance (Typical, Note 2) (C/W) JA DC Input Voltage (Note 3) V SUPPLY PDIP Package* 130 Differential Input Voltage .10V SOIC Package . 160 Output Current (Note 4) .Short Circuit Protected Maximum Junction Temperature (Note 1) . 175C ESD Rating (Note 3) Maximum Junction Temperature (Plastic Package, Note 1) 150C Human Body Model (Per MIL-STD-883 Method 3015.7) . 2000V Maximum Storage Temperature Range -65C to 150C Maximum Lead Temperature (Soldering 10s) 300C Operating Conditions (SOIC - Lead Tips Only) Temperature Range .-40C to 85C *Pb-free PDIPs can be used for through hole wave solder process- Supply Voltage Range (Typical) . 4.5V to 15V ing only. They are not intended for use in Reflow solder processing applications. CAUTION: Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. Maximum power dissipation, including output load, must be designed to maintain junction temperature below 175C for die, and below 150C for plastic packages. See Application Information section for safe operating area information. 2. is measured with the component mounted on an evaluation PC board in free air. JA 3. The non-inverting input of unused amplifiers must be connected to GND. 4. Output is protected for short circuits to ground. Brief short circuits to ground will not degrade reliability, however, continuous (100% duty cycle) output current should not exceed 15mA for maximum reliability. Electrical Specifications V = 5V, R = 1k A = +1, R = 400 C 10pF, Unless Otherwise Specified SUPPLY F V L L (NOTE 9) TEST TEMP. PARAMETER TEST CONDITIONS LEVEL (C) MIN TYP MAX UNITS INPUT CHARACTERISTICS Input Offset Voltage (V)A25-0.83mV IO AFull - - 5 mV Delta V Between Channels A Full - 1.2 3.5 mV IO Average Input Offset Voltage Drift B Full - 5 - V/C V Common Mode Rejection Ratio Note 5 A 25 53 - - dB IO A Full 50 - - dB V Power Supply Rejection Ratio 3.5V V 6.5V A 25 60 - - dB IO S AFull 55 - - dB Input Common Mode Range Note 5 A Full 2.5 - - V Non-Inverting Input (+IN) Current A 25 - 3 8 A AFull - - 20 A +IN Common Mode Rejection Note 5 A 25 - - 0.15 A/V 1 (+I = ) BCMR AFull - - 0.5 A/V +R IN +IN Power Supply Rejection 3.5V V 6.5V A 25 - - 0.1 A/V S AFull - - 0.3 A/V Inverting Input (-IN) Current A 25, 85 - 4 12 A A-40 - 10 30 A Delta -IN BIAS Current Between Channels A 25, 85 - 6 15 A A-40 - 10 30 A FN3393 Rev 9.00 Page 2 of 17 September 30, 2015