DATASHEET HA-5147 FN2910 Rev 1.00 120MHz, Ultra-Low Noise Precision Operational Amplifiers November 6, 2015 The HA-5147 operational amplifier features an unparalleled Features combination of precision DC and wideband high speed Slew rate . 35V/s characteristics. Utilizing the Intersil D. I. technology and advanced processing techniques, this unique design unites low Wide gain bandwidth (A 10) . 120MHz V noise (3.2nV/ Hz) precision instrumentation performance with Low noise 3.2nV/Hz at 1kHz high speed (35V/s) wideband capability. Low V 30V OS This amplifiers impressive list of features include low V OS High CMRR . 120dB (30mV), wide gain bandwidth (120MHz), high open loop gain (1500V/mV) and high CMRR (120dB). Additionally, this flexible High gain 1500V/mV device operates over a wide supply range (5V to 20V) while consuming only 140mW of power. Applications High speed signal conditioners Using the HA-5147 allows designers to minimize errors while maximizing speed and bandwidth in applications requiring Wide bandwidth instrumentation amplifiers gains greater than ten. Low level transducer amplifiers This device is ideally suited for low level transducer signal Fast, low level voltage comparators amplifier circuits. Other applications which can utilize the Highest quality audio preamplifiers HA-5147s qualities include instrumentation amplifiers, pulse or RF amplifiers, audio preamplifiers and signal conditioning Pulse/RF amplifiers circuits. For further design ideas see application note AN553 This device can easily be used as a design enhancement by directly replacing the 725, OP25, OP06, OP07, OP27 and Pin Configuration OP37 where gains are greater than ten. HA-5147 (CERDIP) TOP VIEW 1 8 BAL BAL 2 7 -IN V+ - + 3 6 +IN OUT 4 5 V- NC Ordering Information TEMP. RANGE PKG. DWG. PART NUMBER PART MARKING (C) PACKAGE HA7-5147-2 HA7- 5147-2 -55 to +125 8 Ld CerDIP F8.3A HA7-5147R5254 (Note 1) HA7- 5147R5254 -55 to +125 8 Ld CerDIP with Pb-free Hot Solder DIP Lead Finish (SnAgCu) F8.3A NOTE: 1. Intersil Pb-free hermetic packaged products employ SnAgCu or Au termination finish, which are RoHS compliant termination finishes and compatible with both SnPb and Pb-free soldering operations. Ceramic dual in-line packaged products (CerDIPs) do contain lead (Pb) in the seal glass and die attach glass materials. However, lead in the glass materials of electronic components are currently exempted per the RoHS directive. Therefore, ceramic dual inline packages with Pb-free termination finish are considered to be RoHS compliant. FN2910 Rev 1.00 Page 1 of 11 November 6, 2015HA-5147 Thermal Information Absolute Maximum Ratings T = +25C A Voltage Between V+ and V- Terminals . 44V Thermal Resistance (Typical) (C/W) (C/W) JA JC Differential Input Voltage (Note 2) . 0.7V CERDIP Package (Note 3) 135 50 Output Current Full Short-circuit Protection Maximum Junction Temperature (Hermetic Package) +175C Maximum Storage Temperature Range . -65C to +150C Maximum Lead Temperature (Soldering 10s) +300C Operating Conditions Temperature Range HA-5147-2 -55C to +125C CAUTION: Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 2. For differential input voltages greater than 0.7V, the input current must be limited to 25mA to protect the back-to-back input diodes. 3. is measured with the component mounted on an evaluation PC board in free air. JA Electrical Specifications V = 15V, C 50pF, R 100 . SUPPLY L S TEMP. PARAMETER TEST CONDITIONS (C) MIN TYP MAX UNITS INPUT CHARACTERISTICS Offset Voltage 25 - 30 100 V Full - 70 300 V Average Offset Voltage Drift Full - 0.4 1.8 V/C Bias Current 25 - 15 80 nA Full - 35 150 nA Offset Current 25 - 12 75 nA Full - 30 135 nA Common Mode Range Full 10.3 11.5 - V Differential Input Resistance (Note 4)250.84-M Input Noise Voltage (Note 5) 0.1Hz to 10Hz 25 - 0.09 0.25 V P-P Input Noise Voltage Density (Note 6) f = 10Hz 25 - 3.8 8.0 nV/ Hz f = 100Hz - 3.3 4.5 nV/ Hz f = 1000Hz - 3.2 3.8 nV/ Hz Input Noise Current Density (Note 6)f = 10Hz 25 - 1.7 - pA/ Hz f = 100Hz - 1.0 - pA/ Hz f = 1000Hz - 0.4 0.6 pA/ Hz TRANSFER CHARACTERISTICS Minimum Stable Gain 25 10 - - V/V Large Signal Voltage Gain V = 10V, R = 2k 25 700 1500 - V/mV OUT L Full 300 800 - V/mV Common Mode Rejection Ratio V = 10V Full 100 120 - dB CM Gain-bandwidth Product f = 10kHz 25 120 140 - MHz f = 1MHz - 120 - MHz FN2910 Rev 1.00 Page 2 of 11 November 6, 2015