QS3L384QG8 Renesas

IDTQS3L384 HIGH-SPEED LOW POWER 10-BIT BUS EXCHANGE SWITCH INDUSTRIAL TEMPERATURE RANGE QUICKSWITCH PRODUCTS IDTQS3L384 HIGH-SPEED LOW POWER CMOS 10-BIT BUS EXCHANGE SWITCH FEATURES: DESCRIPTION: Enhanced N channel FET with no inherent diode to Vcc The QS3L384 provides a set of ten high-speed CMOS TTL-compatible 5 bidirectional switches connect inputs to outputs bus switches. The low ON resistance of the QS3L384 allows inputs to be Zero propagation delay, zero added ground bounce connected to outputs without adding propagation delay and without gener- Ultra low power with 0.2A typical Icc ating additional ground bounce noise. The Bus Enable (BE) signals turn the Undershoot clamp diodes on all switch and control inputs switches on. Two bus enable signals are provided, one for each of the upper Two enables control five bits each and lower five bits of the two 10-bit buses. Available in QSOP and TSSOP packages The QS3L384 is characterized for operation at -40C to +85C. APPLICATIONS: Hot-swapping, hot-docking Voltage translation (5V to 3.3V) Power Conservation Capacitance reduction and isloation Bus Isolation Clock Gating FUNCTIONAL BLOCK DIAGRAM A0 B0 A4 B4 A5 B5 A9 B5 BEA BEB The IDT logo is a registered trademark of Integrated Device Technology, Inc. INDUSTRIAL TEMPERATURE RANGE JANUARY 2013 1 c 2013 Integrated Device Technology, Inc. DSC-5772/6IDTQS3L384 INDUSTRIAL TEMPERATURE RANGE HIGH-SPEED LOW POWER 10-BIT BUS EXCHANGE SWITCH (1) PIN CONFIGURATION ABSOLUTE MAXIMUM RATINGS Symbol Description Max Unit (2) VTERM Supply Voltage to Ground 0.5 to +7 V (3) VTERM DC Switch Voltage VS 0.5 to +7 V BEA124 VCC (3) VTERM DC Input Voltage VIN 0.5 to +7 V B0 2 23 B9 VAC AC Input Voltage (pulse width 20ns) 3 V IOUT DC Output Current 120 mA A0 3 22 A9 PMAX Maximum Power Dissipation (TA = 85C) 0.5 W A1 4 21 A8 TSTG Storage Temperature 65 to +150 C B1520 B8 NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause B2 6 19 B7 permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational A2 18 A7 7 sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. A3 8 17 A6 2. VCC terminals. 3. All terminals except VCC . B3 16 B6 9 B4 10 15 B5 CAPACITANCE (TA = +25C, f = 1MHz, VIN = 0V, VOUT = 0V) A4 11 14 A5 (1) Pins Typ. Max. Unit BEB GND 12 13 Control Inputs 3 5 pF Quickswitch Channels (Switch OFF) 5 7 pF QSOP/ TSSOP NOTE: 1. This parameter is guaranteed but not production tested. TOP VIEW PIN DESCRIPTION Pin Names I/O Description A0 - A9 I/O Bus A B0 - B9 I/O Bus B BEA, BEB I Bus Switch Enable (1) FUNCTION TABLE BEA BEB B0 - A4 B5 - B9 Function H H Hi-Z Hi-Z Disconnect LH A0 - A4 Hi-Z Connect H L Hi-Z A5 - A9 Connect LL A0 - A4 A5 - A9 Connect NOTE: 1. H = HIGH Voltage Level L = LOW Voltage Level Z = High-Impedance 2