DATASHEET 1.25V/1.35V/1.5V REGISTERING CLOCK DRIVER WITH PARITY SSTE32882KA1 TEST AND QUAD CHIP SELECT DRAS, DCAS, and DWE), and indicates whether a parity error Description has occurred on the open-drain ERROUT pin (active low). The convention is even parity i.e., valid parity is defined as an even This 28-bit 1:2, or 26-bit 1:2 and 4-bit 1:1, registering clock number of ones across the DIMM-independent data inputs driver with parity is designed for 1.25V, 1.35V and 1.5V VDD combined with the parity input bit. To calculate parity, all operation. DIMM-independent D-inputs must be tied to a known logic state. All inputs are 1.25,1.35V and 1.5V CMOS compatible, except the The DIMM-dependent signals (DCKEn, DODTn, and DCSn) are reset (RESET) and MIRROR inputs which are LVCMOS. All not included in the parity check computation. outputs are 1.25V,1.35V and 1.5V CMOS edge-controlled drivers optimized to drive single terminated 25 to 50 traces in DDR3 To ensure defined outputs from the register before a stable clock RDIMM applications, except the open-drain error (ERROUT) has been supplied, RESET must be held in the low state during output. The clock outputs (Yn and Yn) and control net outputs power-up. QnCKEn, QnCSn and QnODTn are designed with a different The SSTE32882KA1 is available in a 176-ball BGA with strength and skew to compensate for different loading and 0.65mm ball pitch in a 11 x 20 grid. The device pinout supports equalize signal travel speed. outputs on the outer two left and right columns to support easy The SSTE32882KA1 has two basic modes of operation DIMM signal routing. Corresponding inputs are placed in a-way associated with the Quad Chip Select Enable (QCSEN) input. that two devices can be placed back-to-back for four Rank When the QCSEN input pin is open (or pulled high), the modules while the data inputs share the same vias. Each input and component has two chip select inputs, DCS0 and DCS1, and two output is located close to an associated no ball position or on the copies of each chip select output, QACS0, QACS1, QBCS0 and outer two rows to allow low cost via technology combined with QBCS1. This is theQuadCS disable mode. When the the small 0.65mm ball pitch. QCSEN input pin is pulled low, the component has four chip select inputs DCS 3:0 , and four chip select outputs, QCS 3:0 . This is theQuadCS enable mode. Through the remainder of this specification, DCS n:0 will indicate all of the chip select inputs, where n=1 for QuadCS disabled, and n=3 for QuadCS enabled. QxCS n:0 will indicate all of the chip select outputs. The SSTE32882KA1 includes a high-performance, low-jitter, low-skew buffer that distributes a differential clock input (CK and CK) to four differential pairs of clock outputs (Yn and Yn), and to one differential pair of feedback clock outputs (FBOUT and FBOUT). The clock outputs are controlled by the input clocks (CK and CK), the feedback clocks (FBIN and FBIN), and the analog power inputs (AVDD and AVSS). When AVDD is grounded, the PLL is turned off and bypassed for test purposes. The SSTE32882KA1 operates from a differential clock (CK and CK). Data are registered at the crossing of CK going high, and CK going low. The data is either driven to the corresponding device outputs if exactly one of the DCS n:0 input signals is driven low. Based on the control register settings, the device can change its output characterisitics to match different DIMM net topologies. The timing can be changed to compensate for different flight time of signals within the target application. By disabling unused outputs the power consumption is reduced. The SSTE32882KA1 accepts a parity bit from the memory controller on the parity (PAR IN) input, compares it with the data received on the DIMM-independent data inputs (DAn, DBAn, 1.25V/1.35V/1.5V REGISTERING CLOCK DRIVER WITH PARITY TEST AND QUAD CHIP SELECT 1 SSTE32882KA1 7314/9SSTE32882KA1 1.25V/1.35V/1.5V REGISTERING CLOCK DRIVER WITH PARITY TEST AND QUAD CHIP SELECT COMMERCIAL TEMPERATURE RANGE Features Pinout optimizes DDR3 RDIMM PCB layout DDR3-800/1066/1333/1600/1866/2133 rate 1-to-2 Register Outputs and 1-to-4 Clock Pair Outputs support stacked DDR3 RDIMMs Phase Lock Loop clock driver for buffering one differential clock pair (CK and CK) and distributing to four differential outputs Supports LVCMOS switching levels on the RESET and MIRROR inputs Checks priority on DIMM-independent data inputs Supports dynamic 1T/3T timing transaction and output inversion feature for improved timing performance during normal operations and MRS command pass-through Supports CKE Power Down operation modes Supports Quad Chip Select operation features RESET input disables differential input recievers, resets all registers, and disables all output drivers except ERROUT and QnCKEn Provides access to internal control words for configuring the device features and adapting in different RDIMM and system applications Latch-up performance exceeds 100mA ESD > 2000V per MIL-STD883, Method 3015 ESD > 200V using machine model (c = 200pF, R = 0) Available in 176 Ball Grid Array package 1.25V/1.35V/1.5V REGISTERING CLOCK DRIVER WITH PARITY TEST AND QUAD CHIP SELECT 2 SSTE32882KA1 7314/9