Datasheet Serial EEPROM Series Standard EEPROM 2 I C BUS EEPROM (2-Wire) BR24G128-3 General Description 2 BR24G128-3 series is a serial EEPROM of I C BUS Interface Method Features Packages W(Typ) x D(Typ) x H(Max) 2 Completely conforming to the world standard I C N ot Recommended for BUS. All controls available by 2 ports of serial clock New Designs (SCL) and serial data (SDA) Other devices than EEPROM can be connected to DIP-T8 TSSOP-B8 the same port, saving microcontroller port 9.30mm x 6.50mm x 7.10mm 3.00mm x 6.40mm x 1.20mm 1.6V to 5.5V Single Power Source Operation most suitable for battery use 1.6V to 5.5V wide limit of operating voltage, possible FAST MODE 400kHz operation Page Write Mode useful for initial value write at SOP8 TSSOP-B8J factory shipment 5.00mm x 6.20mm x 1.71mm 3.00mm x 4.90mm x 1.10mm Self-timed Programming Cycle Low Current Consumption Prevention of Write Mistake Write (Write Protect) Function Added Prevention of Write Mistake At Low Voltage More than 1 million write cycles SOP- J8 MSOP8 More than 40 years data retention 4.90mm x 6.00mm x 1.65mm 2.90mm x 4.00mm x 0.90mm Noise filter built in SCL / SDA terminal Initial delivery state FFh SSOP-B8 VSON008X2030 3.00mm x 6.40mm x 1.35mm 2.00mm x 3.00mm x 0.60mm Figure 1. BR24G128-3 Power Source Capacity Bit Format Type Package Voltage *1 BR24G128-3 DIP-T8 BR24G128F-3 SOP8 BR24G128FJ-3 SOP-J8 BR24G128FV-3 SSOP-B8 128Kbit 16K8 1.6V to 5.5V BR24G128FVT-3 TSSOP-B8 BR24G128FVJ-3 TSSOP-B8J BR24G128FVM-3 MSOP8 BR24G128NUX-3 VSON008X2030 *1 Not Recommended for New Designs. Product structure : Silicon monolithic integrated circuit This product has no designed protection against radioactive rays www.rohm.com TSZ02201-0R2R0G100230-1-2 2013 ROHM Co., Ltd. All rights reserved. 1/33 TSZ22111 14 001 11.Jun.2019 Rev.005 Datasheet BR24G128-3 Absolute Maximum Ratings (Ta=25C) Parameter Symbol Rating Unit Remark Supply Voltage Vcc -0.3 to +6.5 V 450 (SOP8) Derate by 4.5mW/C when operating above Ta=25C 450 (SOP-J8) Derate by 4.5mW/C when operating above Ta=25C 300 (SSOP-B8) Derate by 3.0mW/C when operating above Ta=25C 330 (TSSOP-B8) Derate by 3.3mW/C when operating above Ta=25C Power Dissipation Pd mW 310 (TSSOP-B8J) Derate by 3.1mW/C when operating above Ta=25C 310 (MSOP8) Derate by 3.1mW/C when operating above Ta=25C 300 (VSON008X2030) Derate by 3.0mW/C when operating above Ta=25C (1) 800 (DIP-T8 ) Derate by 8.0mW/C when operating above Ta=25C Storage Temperature Tstg -65 to +150 C Operating Temperature Topr -40 to +85 C The Max value of Input Voltage/Output Voltage is not over 6.5V. Input Voltage / - -0.3 to Vcc+1.0 V When the pulse width is 50ns or less, the Min value of Input Output Voltage Voltage/Output Voltage is not lower than -1.0V. Junction Tjmax 150 C Junction temperature at the storage condition Temperature Electrostatic discharge voltage VESD -4000 to +4000 V (human body model) (1) Not Recommended for New Designs. Memory Cell Characteristics (Ta=25C, V =1.6V to 5.5V) CC Limit Parameter Unit Min Typ Max (2) Write Cycles 1,000,000 - - Times (2) 40 - - Years Data Retention (2) Not 100% TESTED Recommended Operating Ratings Parameter Symbol Rating Unit Power Source Voltage Vcc 1.6 to 5.5 V Input Voltage VIN 0 to Vcc DC Characteristics (Unless otherwise specified, Ta=-40C to +85C, VCC=1.6V to 5.5V) Limit Parameter Symbol Unit Conditions Min Typ Max Input High Voltage1 V 0.7Vcc - V +1.0 V 1.7VV 5.5V IH1 CC CC (3) Input Low Voltage1 VIL1 -0.3 - +0.3Vcc V 1.7VVCC5.5V Input High Voltage2 V 0.8Vcc - V +1.0 V 1.6VV <1.7V IH2 CC CC (3) Input Low Voltage2 VIL2 -0.3 - +0.2Vcc V 1.6VVCC<1.7V Output Low Voltage1 VOL1 - - 0.4 V IOL=3.0mA, 2.5VVcc5.5V (SDA) Output Low Voltage2 V - - 0.2 V I =0.7mA, 1.6VVcc<2.5V (SDA) OL2 OL Input Leakage Current ILI -1 - +1 A VIN=0 to VCC Output Leakage Current I -1 - +1 A V =0 to V (SDA) LO OUT CC V =5.5V, f =400kHz, t =5ms, CC SCL WR Supply Current (Write) I - - 2.5 mA CC1 Byte write, Page write VCC=5.5V, fSCL=400kHz Supply Current (Read) ICC2 - - 0.5 mA Random read, current read, sequential read Vcc=5.5V, SDA SCL=Vcc Standby Current ISB - - 2.0 A A0,A1,A2=GND,WP=GND (3) When the pulse width is 50ns or less, it is -1.0V. www.rohm.com TSZ02201-0R2R0G100230-1-2 2013 ROHM Co., Ltd. All rights reserved. 2/33 TSZ22111 15 001 11.Jun.2019 Rev.005