REVISION S
RFXXX-XXXXX-XXXXXX-XXXX
DESIGNED & DIMENSIONED
CABLE CALL OUT
OVERALL CABLE LENGTH
IN MILLIMETERS[INCHES] 174: CCA-174 (RG-174 COAXIAL CABLE)
MILLIMETERS OF CABLE
316: CCA-316 (RG-316 COAXIAL CABLE)
0100 MIN. (SEE NOTE 8 & 9)
END 1 CONNECTOR
END 2 PLATING OPTION
-01SP: SMA-P-C-X-ST-CA1 (SEE SHEET 3)
1: GOLD ALL COMPONENTS
-01RP: SMA-P-C-X-RA-CA1 (SEE SHEET 3)
2: GOLD / NICKEL COMBINATION
-01BJ: SMA-J-C-X-ST-BH1 (SEE SHEET 3)
3: ALTERNATE GOLD / NICKEL
-01BR: SMA-J-C-X-ST-BR1 (SEE SHEET 3)
FIG.2
*(LEAVE BLANK FOR -SING OR -XXXXXX
-02SJ: MCX-J-C-X-ST-CA1 (SEE SHEET 3)
CABLE STRIPPING DIMENSIONS
END 2 PREPARATION)
-02RP: MCX-P-C-XX-RA-CA1 (SEE SHEET 3)
PER CONFIGURATIONS
-02SP: MCX-P-C-XX-ST-CA1 (SEE SHEET 4)
(SEE TABLE 1)(SEE NOTES 12,13,14,15)
-03SP: MMCX-P-C-X-ST-CA1 (SEE SHEET 4)
-03RP: MMCX-P-C-X-RA-CA1 (SEE SHEET 4) END 2 CONNECTOR OR PREPARATION mm C -04SP: BNC5-P-C-XX-ST-CA1 (SEE SHEET 4)
-01SP: SMA-P-C-X-ST-CA1 (SEE SHEET 3)
-04BJ: BNC5-J-C-XX-ST-BH1 (SEE SHEET 4)
-01RP: SMA-P-C-X-RA-CA1 (SEE SHEET 3) mm
-05SP: TNC-P-C-XX-ST-CA1 (SEE SHEET 4)
-01BJ: SMA-J-C-X-ST-BH1 (SEE SHEET 3)
-05BJ: TNC-J-C-XX-ST-BH1 (SEE SHEET 5)
-01BR: SMA-J-C-X-ST-BR1 (SEE SHEET 3) mm
-06BJ: NTPE-J-C-XX-ST-BH1 (SEE SHEET 5)
-02SJ: MCX-J-C-X-ST-CA1 (SEE SHEET 3)
-07SP: SMB5-P-C-XX-ST-CA1 (SEE SHEET 5)
-02RP: MCX-P-C-XX-RA-CA1 (SEE SHEET 3)
-07RP: SMB5-P-C-XX-RA-CA1 (SEE SHEET 5)
-02SP: MCX-P-C-XX-ST-CA1 (SEE SHEET 4)
-07BJ: SMB5-J-C-X-ST-BH1 (SEE SHEET 5) -03SP: MMCX-P-C-X-ST-CA1 (SEE SHEET 4)
DO NOT
-13GP: GRF1-P-C-X-ST-CA1
-03RP: MMCX-P-C-X-RA-CA1 (SEE SHEET 4) mm C
SCALE FROM
(316 OPTION ONLY) (SEE SHEET 5)
-04SP: BNC5-P-C-XX-ST-CA1 (SEE SHEET 4)
THIS PRINT
-13GJ: GRF1-J-C-X-ST-CA1 mm C -04BJ: BNC5-J-C-XX-ST-BH1 (SEE SHEET 4)
(316 OPTION ONLY) (SEE SHEET 6)
-05SP: TNC-P-C-XX-ST-CA1 (SEE SHEET 4)
-01SB: SMA-J-C-X-ST-SB1 (SEE SHEET 6)
-05BJ: TNC-J-C-XX-ST-BH1 (SEE SHEET 5)
-01SR: SMA-J-C-X-ST-SR1 (SEE SHEET 6)
-06BJ: NTPE-J-C-XX-ST-BH1 (SEE SHEET 5)
-07SP: SMB5-P-C-XX-ST-CA1 (SEE SHEET 5)
-07RP: SMB5-P-C-XX-RA-CA1 (SEE SHEET 5)
-07BJ: SMB5-J-C-X-ST-BH1 (SEE SHEET 5)
-13GP: GRF1-P-C-X-ST-CA1
(316 OPTION ONLY) (SEE SHEET 5)
END 1 PLATING OPTION
-13GJ: GRF1-J-C-X-ST-CA1
1: GOLD ALL COMPONENTS
(316 OPTION ONLY) (SEE SHEET 6)
2: GOLD / NICKEL COMBINATION
-01SB: SMA-J-C-X-ST-SB1 (SEE SHEET 6)
3: ALTERNATE GOLD / NICKEL
-01SR: SMA-J-C-X-ST-SR1 (SEE SHEET 6)
(SEE SHEET 3 FOR PLATING SPECIFICS)
-SING: SINGLE ENDED (ONE END ONLY, SEE NOTE 11)
-XXXXXX: STRIPPED AND TINNED (THIS END ONLY-
SEE NOTES 11-15 & SHEET 6, FIG. 3)
(SEE FIG. 2) FORMAT: X.X mm
(SEE FIG. 2) FORMAT: X.X mm
(SEE FIG. 2) FORMAT: X.X mm
C
DO NOT LEAVE ANY SPACE BLANK,
FIG.1
EACH MUST CONTAIN A
RFXXX-01SPX-01RPX-XXXX SHOWN
NUMERIC CHARACTER 0 THRU 9.
NOTES:
1. REPRESENTS A CRITICAL DIMENSION.C
2. CABLE CUT LENGTH:
= (LENGTH: XXXX) - (SUBTRACTOR FOR END 1) - (SUBTRACTOR FOR END 2).
C (SEE TABLE 1 FOR SUBTRACTORS)
3. ASSEMBLY TO BE 100% TESTED FOR OPENS & SHORTS.
4. ASSEMBLY TO BE 100% HI-POT TESTED PER TABLE 1. THIS PRODUCT MANUFACTURED
Pb
WITH LEAD-FREE PROCESSING
C 5. AFTER FINAL ELECTRICAL TESTS, LABEL EACH CABLE ASSEMBLY WITH 1 LABEL -ET
F:\DWG\MISC\Mktg\RFXXX-XXXXX-XXXXXX-XXXX-MKT.SLDDRW
6. CRITICALS ON CONNECTOR PRINTS TO BE CHECKED IN PROCESS.
UNLESS OTHERWISE SPECIFIED,
7. FINISHED ASSEMBLIES TO BE PACKAGED PER PACKAGING STANDARD CO-HD-WI-3033-M. PROPRIETARY NOTE
DIMENSIONS ARE IN
-LOCK WASHERS, NUTS, AND GASKETS TO BE SHIPPED UNASSEMBLED. THIS DOCUMENT CONTAINS INFORMATION
MILLIMETERS [INCHES].
CONFIDENTIAL AND PROPRIETARY TO
8. CABLE STOCKED IN INCHES, 1 INCH = 25.4 MILLIMETERS.
TOLERANCES ARE:
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
9. CABLE LENGTHS LONGER THAN 1000 MILLIMETERS ARE NOT SUPPORTED BY S.I. TEST DATA.
OR TRANSFERRED TO OTHER DOCUMENTS OR
DECIMALS ANGLES
DISCLOSED TO OTHERS OR USED FOR ANY
10. MINIMUM BEND RADIUS FOR RG174 = 25.4 [1.00]
.X: 0.3 [.01] 2
PURPOSE OTHER THAN THAT WHICH IT WAS 520 PARK EAST BLVD, NEW ALBANY, IN 47150
RG316 = 12.7 [.50]
.XX: 0.13 [.005]
OBTAINED WITHOUT THE EXPRESSED WRITTEN PHONE: 812-944-6733 FAX: 812-948-5047
.XXX: 0.051 [.0020] CONSENT OF SAMTEC, INC.
11. FOR SING ENDED OR STRIPPED AND TINNED ASSEMBLIES: MAKE A DOUBLE ENDED
e-Mail: info@SAMTEC.com code: 55322
MATERIAL: DO NOT SCALE DRAWING SHEET SCALE: 2:1
ASSEMBLY AT TWICE THE CABLE LENGTH AND TEST BEFORE CUTTING ASSEMBLY IN HALF.
DESCRIPTION:
12. DIM,, AND HAVE A MINIMUM VALUE OF 0.0mm & A MAXIMUM VALUE OF 9.9mm. SEE END 1 AND END 2 ASSEMBLY PRINTS
RF316 OR RF-174 CABLE ASSEMBLY
13. PRODUCTION OF STRIP AND TIN FOR CENTER DIELECTIC USE: A.
DWG. NO.
14. PRODUCTION OF STRIP AND TIN FOR SHIELD USE: D=A+B.
15. PRODUCTION OF STRIP AND TIN FOR JACKET USE: E=A+B+C.
RFXXX-XXXXX-XXXXXX-XXXX
16. FOR -RA TO -RA, CONNECTORS SHOULD BOTH BE ORIENTED UP. (SEE SHEET 6, FIG. 4)
BY: TIM P. 5/3/2005 SHEET OF1 6REVISION S
F:\DWG\MISC\Mktg\RFXXX-XXXXX-XXXXXX-XXXX-MKT.SLDDRW
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PURPOSE OTHER THAN THAT WHICH IT WAS
PHONE: 812-944-6733 FAX: 812-948-5047
OBTAINED WITHOUT THE EXPRESSED WRITTEN
e-Mail: info@SAMTEC.com code: 55322
CONSENT OF SAMTEC, INC.
DESCRIPTION:
DO NOT SCALE DRAWING
RF316 OR RF-174 CABLE ASSEMBLY
DWG. NO.
SHEET SCALE: 1:1
RFXXX-XXXXX-XXXXXX-XXXX
BY: TIM P. 5/3/2005 SHEET OF2 6