TS9011 250mA Low Quiescent Current CMOS LDO SOT-23 SOT-89 TO-92 Pin Definition: Pin Definition: Pin Definition: 1. Ground 1. Ground 1. Ground 2. Output 2. Input 2. Input 3. Input 3. Output 3. Output General Description TS9011 is a positive voltage regulator developed utilizing CMOS technology featured very low power consumption, low dropout voltage and high output voltage accuracy. Built in low on-resistor provides low dropout voltage and large output current. A 1uF or greater can be used as an output capacitor. TS9011 are prevented device failure under the worst operation condition with both thermal shutdown and current fold-back. These series are recommended for configuring portable devices and large current application, respectively. Features Ordering Information Dropout Voltage Typically 0.4V Io=200mA Part No. Package Packing (Vo=5V) TS9011xCX RF SOT-23 3Kpcs / 7 Reel Output Current up to 250mA TS9011xCY RM SOT-89 1Kpcs / 7 Reel Low Power Consumption, 2uA(typ) Vo=5V TS9011xCT A3 TO-92 2Kpcs / Ammo Output Voltage 2% TS9011xCT B0 TO-92 1Kpcs / Bulk Internal Current Limit Thermal Shutdown Protection Note: Where x denotes voltage option, available are A=1.5V Applications D=1.8V Battery-operated systems K=2.5V Microprocessor reset circuitry P=3.0V Memory battery back-up circuits S=3.3V Power-on reset circuits 5=5V Power failure detection Contact factory for additional voltage options. System battery life and charge voltage monitors Block Diagram Typical Application Circuit * Tantalum capacitor for Input & Output capacitor are recommended 1/1 Version: E07 TS9011 250mA Low Quiescent Current CMOS LDO Absolute Maximum Rating Parameter Symbol Limit Unit Input Supply Voltage V 12 V IN Output Current I P / (V V ) V O D IN O SOT-23 0.30 Power Dissipation P W SOT-89 D 0.50 TO-92 0.625 SOT-23 333 o Thermal Resistance - Junction to Ambient SOT-89 R 200 C/W JA TO-92 160 o Operating Ambient Temperature T -40 ~ +85 C OPR o Junction Temperature Range T -40 ~ +150 C J o Storage Temperature Range T -65 ~ +150 C STG Notes: Stress above the listed absolute rating may cause permanent damage to the device. o Electrical Characteristics (Ta = 25 C, unless otherwise noted) Parameter Conditions Min Typ Max Unit TS90115 4.90 5.0 5.10 TS9011S 3.23 3.3 3.36 V =Vo + 1V, TS9011P 2.94 3.0 3.06 IN Output Voltage V Io =40mA, TS9011K 2.45 2.5 2.55 TS9011D 1.76 1.8 1.83 TS9011A 1.47 1.5 1.53 Maximum Output Current V =Vo+1V, 250 -- -- mA IN Input Stability V +1V Vin V +2V, Io=1mA -- 0.2 0.3 % O O V =Vo+1V, TS90115 IN -- 40 80 1mAI 100mA TS9011S L TS9011P Load Regulation (Note1) mV V =Vo+1V, TS9011K IN -- 40 90 1mAI 80mA L TS9011D TS9011A Io=250mA TS90115 -- 400 600 Io=200mA TS9011S -- 400 650 Io=160mA TS9011P -- 400 700 Dropout Voltage (Note 2) mV Io=160mA TS9011K -- 400 700 Io=120mA TS9011D -- 400 750 Io=100mA TS9011A -- 850 1000 Quiescent Current V =Vo+1V, Io=0A -- 2 5 uA IN Output Current Limit V < 0.4V -- 400 -- mA OUT Power Supply Rejection Ratio At f=100KHz, Io=10mA, -- 30 -- dB Output Voltage Temperature o -- 100 -- ppm/ C Coefficient (Note 3) Notes: 1. Regulation is measured at constant junction temperature, using pulsed ON time. 2. Dropout is measured at constant junction temperature, using pulsed ON time, and the criterion is V inside OUT target value +/-2%. 3. Guaranteed by design. 2/2 Version: E07