6 <:=+<176 0--< ,% /)+.), --* 00&+ *4 3)1( )& 00&+ *4 -> =5=4)<1>- :)=5) 1 7:,-: +)6:- =4<.:75<0-8:7476/-,= -7.5)6=)44A87 -:-,0)6,<774 )6,<774 ):-16<-6,-,.7:7++) 176)4= -)6,47 >74=5 - )8841+)<176 1,- -4-+<1767.87 -:-,)8841+)<176-9=185-6<.7:- <-6,-, = - 8:7,=+<17678-:)<176 1 )>)14)*4- 7+)<7: <)<176):A ) -5*4A =8841-, 1<0 )+37. 774 1- -5*4A &1:- 1,- :76<7. 774 1>7< 16 7+)<7: 1,- 1- )6, :15816/ -5*4A 774 :)5- -- 16 <:=+<176 0--< 7>16/ ) )<+0-< ,2= <5-6< &0--4 <)<176):A )6,4- 7>16/ )6,4- 0- )6, :15816/ 774 -5*4A1 )B 755-:+1)4 /:),-<774 )6,1 ,- 1/6-,8:15):14A.7:.1-4,16 <)44)<176 :-8)1: 5)16<-6)6+- 7:3 7:8:7<7<A816/ 1616,= <:1)4 +755-:+1)4 7:16 <1<=<176)4)8841+)<176 :7,=+<+:158-, 1<0<01 <774 144 5--<<0-+:1580-1/0<:-9=1:-5-6<.7:0)6,<774 16<0-)88:78:1)<- )8841+)<176 8-+1.1+)<176 *=<5)A67<+7584A 1<07<0-:.-)<=:-8):)5-<-: 7.<0- 8-+1.1+)<176 A+7 4-+<:761+ 7..-: )>):1-<A7.<774 <7 )<1 .AA7=:8-:.7:5)6+-:-9=1:-5-6< 7: ),,1<176)416.7:5)<176 +76<)+<<0- -+061+)4 1 <)6+- -6<-:)< )/& )& )& 00&+ *4 00&+ *4 -1-/ -1-/ 00&+ *4 00&+ *4 -,1 1 -,1 1 )5& ,021)-, +&1&/ 1/). &,1( /1 2+ &/ /1 2+ &/ +)*4 ++ , ++ , <7 4)6, <7 <7 ( 4 4 -:1- -:1- <7 <7 ( ( (5) =8841-, 1<0<0-,1-) -5*4A 4 7)>)14)*4- -8):)<-4A 76<)+<<0- :7,=+< 6.7:5)<176 -6<-: *-47 .7: 8-+1.1++76<)+<8):<6=5*-: Figure 1 any contacts. PROCRIMPER III Hand Tool Assembly 585481 consists of Die Assembly 585482 and PROCRIMPER III Hand Tool Frame 3549401. The die assembly consists of crimping dies and a locator assembly. Reasons for reissue are provided in Section 11, Read these instructions thoroughly before crimping REVISION SUMMARY. 01 +76<:744-,,7+=5-6<1 =*2-+<<7+0)6/- A+7 4-+<:761+ 7:87:)<176 )::1 *=:/ 7. 44 6<-:6)<176)4 1/0<- -:>-, % 7:4)<- <:->1 176)6-/176)4 = <75-: -:>1+- 47/7)6, A+7 4-+<:761+ ):-<:),-5):3 >1 1<7=: -* 1<-)< 333 14 -&*& 1/-,) 0 -+ :),-5):3 <0-:8:7,=+< 47/7 )6,+758)6A6)5- = -,):-<0-8:78-:<A7.<0-1::- 8-+<1>-7 6-: % % && )) * % ( % & % & Figure 2 screw just enough to hold the dies in place. Do not tighten the screw completely at this time. The tool features a tool frame with a stationary jaw and handle, a moving jaw, a moving handle, and an 5. Place the wire crimper and insulation crimper so adjustable ratchet that ensures full contact crimping. that their chamfered sides and their marked The tool frame holds a die assembly with two surfaces face outward, when mounted in the stationary jaw of the tool frame. crimping sections. 6. Insert the two die retaining pins. The die assembly features a wire anvil, an insulation anvil, a wire crimper, and an insulation crimper. 7. Insert the long die retaining screw through the jaw and through both crimper dies, and tighten the Attached to the outside of the frame is a locator screw just enough to hold the dies in place. Do not assembly, which contains a locator, a spring retainer, tighten the screw completely at this time. and a contact support. 8. Carefully close the tool handles, making sure Die retaining pins and die retaining screws are used that the anvils and crimpers align properly. to position and secure the dies in the tool frame. A Continue closing the tool handles until the ratchet nut is used on the upper die retaining screw to hold in the tool frame has engaged sufficiently to hold the locator assembly in place. the anvils and crimpers in place, then tighten both die retaining screws. 9. Place the locator assembly over the end of the long screw, and position the locator assembly against the side of the tool jaw. 1. Open the tool handles and remove the two die retaining screws from the tool jaws. 10. Place the nut onto the end of the long screw and tighten the nut enough to hold the locator 2. Place the wire anvil and insulation anvil so that assembly in place, while still allowing the locator to their chamfered sides and their marked surfaces slide up and down. face outward, when mounted in the moving jaw of the tool frame. 11. To disassemble, close the tool handles until the ratchet releases, remove the nut, the locator 3. Insert the two die retaining pins. assembly, the two die retaining screws, and the 4. Insert the short die retaining screw through the four die retaining pins, and slide the anvils and jaw and through both anvil dies, and tighten the crimpers out of the tool jaws. ( &