TB67S109AFTG,EL Toshiba

TB67S109AFTG/FNG TOSHIBA BiCD Integrated Circuit Silicon Monolithic TB67S109AFTG, TB67S109AFNG CLOCK-in controlled Bipolar Stepping Motor Driver The TB67S109A is a two-phase bipolar stepping motor driver using a PWM chopper. The clock in decoder is built in. FTG Fabricated with the BiCD process, rating is 50 V/4.0 A . Features BiCD process integrated monolithic IC. Capable of controlling 1 bipolar stepping motor. P-WQFN48-0707-0.50-003 PWM controlled constant-current drive. Weight 0.10g (typ.) Allows full, half, quarter, 1/8, 1/16, 1/32 step operation. Low on-resistance (High + Low side=0.49 (typ.)) MOSFET FNG output stage. High efficiency motor current control mechanism (Advanced Dynamic Mixed Decay) High voltage and current (For specification, please refer to absolute maximum ratings and operation ranges) Error detection (TSD/ISD) signal output function HTSSOP48-P-300-0.50 Built-in error detection circuits (Thermal shutdown (TSD), over-current Weight 0.21g (typ.) shutdown (ISD), and power-on reset (POR)) Built-in VCC regulator for internal circuit use. Chopping frequency of a motor can be customized by external resistance and capacitor. Multi package lineup TB67S109AFTG: P-WQFN48-0707-0.50-003 TB67S109AFNG: HTSSOP48-P-300-0.50 Note) Please be careful about thermal conditions during use. 2014-2020 1 2020-2-4 Toshiba Electronic Devices & Storage Corporation TB67S109AFTG/FNG Pin assignment (TB67S109A) (Top View) 34 33 32 31 30 29 28 27 26 25 36 35 24 NC 37 NC 23 NC LO 38 22 GND DMODE0 39 21 OUTB- 40 GND 20 OUTB- 41 VREFB FTG 19 GND 42 VREFA 18 GND OSCM 43 17 OUTA- 44 CW/CCW 16 OUTA- MO 45 15 GND 46 DMODE1 14 NC 47 DMODE2 13 NC 48 NC 1 2 3 4 5 6 7 8 9 10 11 12 Please solder the four corner pins of the QFN package and the exposed pad to the GND area of the PCB. (Top View) OSCM 1 48 VREFA NC 47 2 VREFB 46 CW/CCW 3 GND 4 DMODE0 45 MO DMODE1 LO 5 44 NC NC 6 43 DMODE2 NC 7 42 CLK 8 41 VCC ENABLE 9 40 NC VM 10 39 RESET GND 11 NC 38 NC 12 37 NC RSA 13 36 RSB FNG RSA 14 35 RSB NC 15 34 NC 16 OUTA+ 33 OUTB+ OUTA+ 17 32 OUTB+ NC 18 31 NC NC 19 30 NC GND 20 GND 29 21 NC NC 28 OUTA- 22 OUTB- 27 OUTA- 23 26 OUTB- GND 24 25 GND Please solder the exposed pad of the HTSSOP package to the GND area of the PCB. 2 2020-2-4 NC NC CLK NC ENABLE VCC RESET NC GND VM NC NC RSA RSB RSA RSB NC NC OUTA+ OUTB+ OUTA+ OUTB+ NC NC