ZVT-16/25-IF ZVT-16/25-IF APPLICATIONS The ZVT-E-IF-10K3A1 is an NTC type thermistor, sealed in a stainless steel probe with 1mtr. CONTROLLER & 10K3A1-SENSOR INSTALLATION of white PTFE sensor connections and earth leads. It is designed for use with ZVT-16-IF and ZVT-25-IF flicker inhibited power temperature INSTALLATION X10612 controllers. See Data sheets X10511 and X10542 respectively. INSTALLATION INSTRUCTIONS 1. Peel adhesive back off dial and fit over 10mm panel hole. DIMENSIONS AND SPECIFICATIONS 2. See the table below for heatsink requirements & expected ambient temperature, to calculate the maximum current rating. THIS UNIT MUST BE EARTHED 3. Check that the voltage rating & sensor type is correct. 4. For ZVT-16-IF only: Apply a thin smear of heatsink paste for good thermal coupling and Insert unit through 10mm panel hole. Affix dial and extra heatsink as appropriate, ensuring equipotential bonding (Earth bonding) and tighten front nut.. 5. Before fitting control knob, turn temperature control fully anti-clockwise to the mechanical stop. 6. Fit and align control knob to coincide with the dial mark below 0C 7. Make wire connections to rear terminals. To monitor supply and load conditions fit neons across the relevant terminals. MAXIMUM OUTPUT RMS CURRENT (A) Max unit temperature 20C 50C 65C Without extra heatsink 10 7 5 +Heatsink 100 x 100 x 3mm 14 12 10 NOTE: Good thermal bonding of sensor is required, where appropriate, to ensure controller +Heatsink 170 x 170 x 3mm 16 16 15 performance reaction time, i.e. for thermal bonding of sensor to metal heatsink, it is recommended that heatsink paste is used. OPERATION 8. Note that unit will not operate or indicate correctly and Triac will not latch on with RECOMMENDATION loads of less than 200W. Other documents, which may be appropriate for your applications, are available on request, 9. Set Prop. Band (internally 25-IF or via rear panel 16-IF ) fully anti-clockwise. CODE IDENTITY DESCRIPTION 10. Switch and turn dial to required temperature and allow system to heat up to a steady X10229 RFI Filter recommendation - addressing EMC directive. state. If temperature is unstable turn Prop. Band clockwise in small steps over X10213 ITA Interaction, uses for phase angle and for burst fire control. several minutes until stable conditions are obtained, characterised by a steady output X10255 SRA Safety requirements - addressing the Low Voltage Directive On/Off ratio. (LVD) including :-Thermal data/cooling Live parts warning 11. If output remains off, check for open or short circuit in sensor circuit, and if output & Earth requirements Fusing recommendations. stays on, check position of sensor relative to heated zone. The correct sensor X10511 ZVT1/2-16 16A Zero voltage Temperature controller temperature set points for resistance are:- X10542 ZVT1/2-25 25A Zero voltage Temperature controller AP02/4 COS UAL Conditions of sale RoHS Compliant 0C 32.6K NOTE. It is recommended that installation and maintenance of this equipment should be 25C 10K Directive carried out with reference to the current edition of the I.E.E. Wiring Regulations BS7671, by 100C 680 suitably qualified/trained personnel. The regulations contain important requirements regarding 2002/95/EC the safety of electrical equipment. For International Standards refer to I.E.C. Directive I.E.C. 950. 12. Do not use Megger or other high voltage equipment as the voltage rating may be exceeded and damage the internal components. ORDER CODE: State part number: ZVT-E-IF-10K3A1 Enclosed, inhibited flicker sensor. UNITED AUTOMATION LIMITED CE MARKING 1Southport Business Park Tel: 0044 (0) 1704 516500 Main This product carries a CE marking. For further information, the see the Kew Tel: 0044 (0) 1704 516516 Sales RECOMMENDATION section or contact our sales desk. Southport, PR8 4HQ Fax: 0044 (0) 1704 516501 ENGLAND Enquiry united-automation.com Page No. 2 of 2 Issue 2 Date 12/03 X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for united automation manufacturer: Other Similar products are found below : F175-25A SSC-25 QVR-TB-RFI CSR604A PAC2 CSR1004A AFM-11 QVR/S-RFI 17 CSR1504A PSR-25