8 7 6 5 4 3 2 1 VICOR CONFIDENTIAL REV. DESCRIPTION DATE APPROVED THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR HEREWITH IS NOT TO BE REPRODUCED, USED OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT THE PERMISSION OF VICOR CORP. 1 RELEASED PER E053437 LEK 11/15/05 EF 2 REVISED PER E090758 AR 05/08/09 REJH F F 3 REVISED PER E091807 GCK 10/8/09 MM 4 REDRAWN PER E100902 DCS 7/14/10 KUK 5 REVISED PER E120702 ZMB 07/31/12 REJH <> <> SEE NOTE 6 .16 TYP 30 DRILL THRU (12) PL1285 .010 SEE NOTE 5 (6) PL. E E .40 MAT L TO BE REMOVED C L R.110 MAX (12) PL. 1.270 1.470 <> D D C L .209 .650 (2) PL. <> SEE NOTE 5 .190 1.300 .49 -A- <> .100 2.28 C C <> .005 .410 B B NOTES: 1. MATERIAL: EXTRUSION SEE SHEET 2 OF 2 2. REMOVE ALL BURRS AND SHARP EDGES. <>3. CLEAR FINISH, RoHS COMPLAINT PER CST-0001, LATEST REVISION PER DRAWN BY DATE SWD VICOR A)CHROMIUM FREE, OR D.P. KELLY 11/97 B)TRIVALENT CHROMIUM IN ACCORDANCE WITH MIL-DTL-5541, TYPE II, CLASSS 1A OR 3. SEE CST-0003 FOR TYPES OF AVAILABLE FINISHES. UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE : INCH / MM 4. < DENOTES CRITICAL CHARACTERISTIC FOR LOT INSPECTION. HS CFG LONG .4H, LOW TOLERANCES ARE: 5. DIMENSION APPLIES AT SURFACE -A- (12) PL. DECIMALS ANGLES A A FLOW, THRU HOLE X.XX X.X = 0.01 0.25 1 6. MACHINED SURFACE TO BE .010 MAX BELOW SURFACE -A- (6) PL. X.XXX X.XX = 0.005 0.127 7. DIMENSIONS ARE INCHES ONLY. SIZE CAGE CODE DWG NO REV THIRD ANGLE PROJECTION C 67131 30719 5 2:1 2 SCALE SHEET OF 1 DO NOT SCALE DRAWING 8 7 6 5 4 3 2 18 7 6 5 4 3 2 1 VICOR CONFIDENTIAL REVISIONS THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR HEREWITH IS NOT TO BE REPRODUCED, USED OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT REV DESCRIPTION DATE APPROVED THE PERMISSION OF VICOR CORP. SEE SHEET 1 F F 3 1.5 EACH SIDE OF VERT E E 1.756 R.018 .023 (2) PL. (R .035 ) .038 (16) PL. SEE DETAIL A R.035 D D .040 .080 (2) PL031 .410 R.030 .252 .235 .200 (8) PL110 * .060 (4) PL. * .133 (5) PL. * .060 C * .058 C * .030 (2) PL. DETAIL A * .281 SCALE 8 : 1 +.020 .004 1.470 -.000 (2) PL. B B PROFILE COMMON FOR 30719 32174 SWD DRAWN BY DATE VICOR ANUYUGH 05/08/09 NOTES: RAGIPANI 1. MAT L: ALUMINUM 6063-T5 UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE : INCH / MM 2. * DENOTES DIMENSION TO THEORETICAL SHARP CORNER. HS CFG LONG .4H LOW TOLERANCES ARE: 3. DIMENSIONS ARE INCHES ONLY. DECIMALS ANGLES A A FLOW, THRU HOLE, EXTRUSION X.XX X.X = 0.01 0.25 1 X.XXX X.XX = 0.005 0.127 SIZE CAGE CODE DWG NO REV THIRD ANGLE PROJECTION C 67131 30719 5 SCALE 2:1 2 2 SHEET OF DO NOT SCALE DRAWING 8 7 6 5 4 3 2 1