SIP32460DB-T2-GE1 Vishay

SiP32460, SiP32461, SiP32462 www.vishay.com Vishay Siliconix 50 m , Slew Rate Controlled Load Switch in WCSP DESCRIPTION FEATURES The SiP32460, SiP32461, and SiP32462 are slew rate Low input voltage, 1.2 V to 5.5 V controlled integrated high side load switches that operate Low R , 54 m /typ. at 3 V on over the input voltage range from 1.2 V to 5.5 V. Slew rate control This series of design features slew rate control, reverse Compatible with 1.2 V to 3.3 V logic blocking when switch is off, output discharge, and control 7.5 s turn-on time at 5 V (SiP32462) Available logic pulldown. The devices are logic high enabled. Reverse current blocking when switch is off The SiP32460, SIP32461, and SiP32462 are available in compact wafer level WCSP package, WCSP4 Integrated output discharge switch (SiP32461) 0.76 mm x 0.76 mm with 0.4 mm pitch. Integrated pulldown resistor at EN For enable low see SiP32467 and SiP32468 4-bump WCSP package Material categorization: for definitions of compliance please see www.vishay.com/doc 99912 APPLICATIONS Smart phones GPS and portable media players Tablet computers Medical and healthcare equipment Industrial and instrumentation Game consoles TYPICAL APPLICATION CIRCUIT V IN IN OUT V OUT SiP32460, SiP32461, SiP32462 C C IN OUT EN EN GND GND GND Fig. 1 - Typical Application Circuit ORDERING INFORMATION t on PART NUMBER PACKAGE R MARK CODE TEMPERATURE RANGE DISCHARGE (s) SiP32460DB-T2-GE1 WCSP4 (2x2), 0.4 mm pitch 300 No AF -40 C to +85 C SiP32461DB-T2-GE1 WCSP4 (2x2), 0.4 mm pitch 300 Yes AG -40 C to +85 C SiP32462DB-T2-GE1 WCSP4 (2x2), 0.4 mm pitch 7.5 No AH -40 C to +85 C S20-0532-Rev. E, 06-Jul-2020 Document Number: 67754 1 For technical questions, contact: powerictechsupport vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000SiP32460, SiP32461, SiP32462 www.vishay.com Vishay Siliconix ABSOLUTE MAXIMUM RATINGS PARAMETER CONDITIONS LIMIT UNIT Supply input voltage V Reference to GND -0.3 to 6.5 IN Output voltage V Reference to GND -0.3 to 6.5 OUT V a Output voltage V Pulse at 1 ms reference to GND -1.6 OUT Enable input voltage EN Reference to GND -0.3 to 6.5 Maximum continuous switch current 1.2 A Maximum pulse switch current Pulse at 1 ms, 10 % duty cycle 2 ESD rating (HBM) 4000 V Thermal resistance 205 C/W Maximum power dissipation T = 25 C 300 mW A Temperature Operating temperature -40 to +85 Operating junction temperature 125 C Storage temperature -65 to +150 Note a. Negative current injection up to 300 mA Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. RECOMMENDED OPERATING RANGE ELECTRICAL PARAMETER MINIMUM TYPICAL MAXIMUM UNIT Input voltage (V ) 1.2 - 5.5 IN V Output voltage (V ) 1.2 - 5.5 OUT SPECIFICATIONS TEST CONDITIONS LIMITS UNLESS OTHERWISE SPECIFIED PARAMETER SYMBOL UNIT V = 1.2 V to 5.5 V, T = -40 C to +85 C IN A MIN. TYP. MAX. (typical values are at 25 C) Power Supply Quiescent current I V = 3.3 V, I = 0 mA - 4.5 7 Q IN OUT Shutdown current I OUT = GND - 0.01 2 SD Off switch current I EN = GND, OUT = GND - 0.01 2 A DS(off) OUT = 5 V, IN = 1.2 V, EN = 0 V, (measured at IN pin) - 0.01 1 Reverse blocking current I (in)RB OUT = 5 V, IN = 0 V, EN = 0 V, (measured at IN pin) - 0.01 1 Switch Resistance I = 500 mA, V = 1.2 V, T = 25 C - 95 150 OUT IN A I = 500 mA, V = 1.5 V, T = 25 C - 80 120 OUT IN A On resistance R I = 500 mA, V = 1.8 V, T = 25 C - 70 100 m DS(on) OUT IN A I = 500 mA, V = 3 V, T = 25 C - 54 65 OUT IN A I = 500 mA, V = 5 V, T = 25 C - 50 65 OUT IN A When V = 3 V at 25 C - 80 - IN Discharge switch on resistance R PD When V = 1.8 V at 25 C - < 200 - IN EN pin pulldown resistor R EN = 1.2 V 1 2.6 5 M EN On resistance temperature TC - 2800 - ppm/C RDS coefficient On/off Logic EN input low voltage V V = 1.5 V 0.4 - - IL IN V EN input high voltage V V = 5.5 V - - 1 IH IN S20-0532-Rev. E, 06-Jul-2020 Document Number: 67754 2 For technical questions, contact: powerictechsupport vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000