1-CHANNEL RADIO MODULAR RECEIVER ROM-01 CONNECTION MOUNTING MANUAL INSTRUCTION 1. Disconnect power supply by the phase fuse, the circuit-breaker or the switch- disconnector combined to the proper circuit. 2. Check if there is no voltage on con- ZAMEL Sp. z o.o. nection cables by means of a special measure equipment. 3. Connect the cables with the terminals in ul. Zielona 27, 43-200 Pszczyna, Poland accordance with the installing diagram. tel. +48 (32) 210 46 65, fax +48 (32) 210 80 04 4. Mount ROM-01 device on a TH-35 rail. www.zamelcet.com, e-mail: marketing zamel.pl 5. Switch on the power supply from the mains. TECHNICAL DATA DESCRIPTION ROM-01 1-channel radio modular receiver CAPACITY ROM-01 can be mounted in distribution Input (supply) terminals: L, N Input rated voltage: 230V AC boards on the TH-35 rail and can realise Input voltage tolerance: -15 +10 % 1000W 500W radio control functions using any of EXTA Nominal frequency: 50 / 60 Hz FREE system transmitters. Any electric Nominal power consumption: 0,45 W 250W 375W system realising radio system functions Optic signalling of power supply: LED green diode can be connected to the device relay Number of operation modes: 5 output (e.g. wired devices of EXTA home Number of channels: 1 automation, relay-contactor systems and APPLICATION Transmission: radio 868,32 MHz others). Coding way: unidirectional Radio modular receiver ROM-01 Coding: addressing transmission operates as a receiver of P-257/2 FEATURES Maximum number of remote controls: 32 2-channel remote control (control Range: up to 300 m in the open area of lighting operation in front of the cooperation with wireless EXTA FREE garage gate). P-257/2 remote control Time adjustment: 1 sec. 18 hours (every second) system transmitters, can also operate the garage gate by Optic signalling of relay status: LED red diode 1-channel radio receiver mounted on means of ROB-01/12-24V radio gate Relay output clamps: 12, 11, 14 a TH-35 rail in a distribution board, controller. Relay contact parameters: 1NO/NC 8 A / 250 V~ AC1 2000 VA five operation modes: switching on o mode, switching off, monostable, bista- Ambient temperature range: -10 +55 C 2 ble, time, Section of connecting cables: up to 2,5 mm one output relay NO/NC (dry contacts), Operating position: free wide range of operation (up to 300 m), Casing mounting: TH-35 rail (according to EN 60715) power supply and relay operation are Casing protection degree: IP20 (EN 60529) optically signalled, Protection level: II integration possibility with wired control Overvoltage category: II systems (e.g. exta home automation), Pollution degree: 2 connection possibility of ANT-01 an- tenna mounted not in the distribution Surge voltage: 1 kV (EN 61000-4-5) board, Dimensions: monomodular casing (17,5 mm) 90 x 17,5 x 66 mm possibility of widening operation range Weight: 0,083 kg by means of RTN-01 retransmitter. Reference standard: EN 60669, EN 60950, EN 61000 The device is designed for sin- APPEARANCE gle-phase installation and must be installed in accordance with standards valid in a particular country. The device should be Input (supply) terminals (L, N) connected according to the CAUTION details included in this operat- ing manual. Installation, connection and control The ZAMEL company devices Antenna should be carried out by a qualified electrician which are characterised staff, who act in accordance with the service with this sign can cooperate manual and the device functions. with each other. In case of casing dismantling an electric shock Optic signalling of input voltage may occur, and the guarantee is lost then. Be- Optic signalling of relay status fore installation make sure the connection ca- WARRANTY CARD bles are not under voltage. The cruciform head Antennas socket screwdriver 3,5 mm should be used to instal the device. Improper transport, storage, and use of There is 24 months guarantee on the product Programming push-buttons the device influence its wrong functioning. It is 1. ZAMEL provides a two-year warranty for its products. not advisable to instal the device in the following 2. The ZAMEL warranty does not cover: a) mechanical defects resulting from transport, loading / unloading or other circumstances b) defects resulting from incorrect installation or operation of ZAMEL products c) defects resulting from any changes made by CUS- cases: if any device part is missing or the device TOMERS or third parties, to products sold or equipment necessary for the correct operation of products sold d) defects resulting is damaged or deformed. In case of improper from force majeure or other aleatory events for which ZAMEL is not liable e) power supply (batteries) to be equipped with a device functioning of the device contact the producer. in the moment of sale (if they appear) 3. All complaints in relation to the warranty must be provided by the CUSTOMER in writing to the retailer after discovering a defect. The symbol means selective 4. ZAMEL will review complaints in accordance with existing regulations. collecting of electrical and electronic 5. The way a complaint is settled, e.g. replacement of the product, repair or refund, is left to the discretion of ZAMEL. 6. Guarantee does not exclude, does not limit, nor does it suspend the rights of the PURCHASER resulting from the discrepancy equipment. Relay output terminals (12, 11, 14) between the goods and the contract. It is forbidden to put the used equipment together with other waste. Salesman stamp and signature, date of sale VER. 004 11.07.2011OPERATION TIME PROGRAMMING The device can operate in five modes: 1s 2s ns MONOSTABLE BISTABLE SWITCH ON TIME the relay operates only (one push-button) the the device switches on the device switches while pressing transmit- device changes relay after pressing the push- off according to the ters push-button. status cyclically always button. adjusted time (tp), after pressing the same push- SWITCH OFF but it may be switched off before button. the device switches off adjusted time finishes. Default Press PROG push-button of ROM-01 device for a longer time till Press PROG push-button of ROM-01 After the adjusted time is after pressing the push- settings - 15 seconds. LED red diode switches on (constant signal). Next release PROG device and then release it. LED red finished (the number of LED button. push-button. Wait (for about 5 seconds) till LED red diode switches diode switches off and then switches on red diode flashes) press CAUTION Adjusted time can- on (first signal pulsates, next the signal is constant). (signal pulsates). Every LED diode PROG push-button and then not be deleted. pulse equals 1 second. release it - TIME IS ADDED. Maximum time is 18 hours. RADIO TRANSMITTERS DELETION RADIO TRANSMITTERS PROGRAMMING Press PROG push-button of ROM-01 After 5 seconds LED red diode switches on Release the push-button in ROM-01 device for a longer time. (signal pulsates) and then it switches off. - MEMORY IS DELETED. MONOSTABLE mode: COOPERATION AND OPERATING RANGE Symbol ROP-01 ROP-02 ROB-01 SRP-02 SRP-03 RWG-01 RWL-01 ROM-01 ROM-10 RDP-01 RTN-01 RNK-02 180 m 200 m 200 m 200 m 200 m 250 m 180 m 250 m 250 m 180 m 250 m Press transmitters Press PROG push-button of ROM-01 device Release transmitters push- RNK-04 180 m 200 m 200 m 200 m 200 m 250 m 180 m 250 m 250 m 180 m 250 m Press the same transmitters push- push-button for for a longer time until LED red diode switches on button. LED red diode switches -button and release it. LED red dio- P-256/8 230 m 250 m 250 m 250 m 250 m 300 m 200 m 300 m 300 m 230 m 300 m a longer time. (constant signal). Next release PROG push-button. on (first signal pulsates, de switches on (the signal pulsates) P-257/4 (2) 180 m 200 m 200 m 200 m 200 m 250 m 180 m 250 m 250 m 180 m 250 m next the signal is constant). and next it switches off RNM-10 230 m 250 m 250 m 250 m 250 m 300 m 200 m 300 m 300 m 230 m 300 m - THE TRANSMITTER IS ADDED. BISTABLE mode: RNP-01 160 m 180 m 180 m 180 m 180 m 200 m 160 m 200 m 200 m 160 m 200 m RNP-02 160 m 180 m 180 m 180 m 180 m 200 m 160 m 200 m 200 m 160 m 200 m RNL-01 160 m 180 m 180 m lack* lack* 200 m 160 m 200 m 200 m 160 m 200 m RTN-01 200 m 200 m 200 m 200 m 200 m 250 m 200 m 250 m 250 m 200 m 250 m RCR-01 160 m 180 m 180 m lack* lack* 200 m 160 m 200 m 200 m 160 m 200 m RTI-01 160 m 180 m 180 m 180 m 180 m 200 m 160 m 200 m 200 m 160 m 200 m RXM-01 230 m 250 m 250 m 250 m 250 m 300 m 200 m 300 m 300 m 230 m 300 m Press PROG push-button of ROM-01 device Press the transmitters push-button Release transmitters push-button. LED * - 1-channel transmitters do not cooperate with roller blind controllers. for a longer time until LED red diode switches on for a longer time. LED red diode red diode switches on (the signal pulsates), CAUTION: The given range concerns open area - an ideal condition without any natural or artificial obstacles. If there are some obstacles between a transmitter and a receiver, (constant signal). Next release PROG push-button. switches on (first signal pulsates, next the LED red diode switches off - it it is advisable to decrease the range according to: next the signal is constant). wood and plaster: from 5 to 20 %, bricks: from 10 to 40 %, reinforced concrete: from 40 to 80 %, metal: from 90 to 100%, glass: from 10 to 20 %, Over- and underground medium means the TRANSMITTER IS ADDED. and high electrical power lines, radio and television transmitters, GSM transmitters set close to a device system have also a negative influence on the range. SWITCH ON/SWITCH OFF mode (two push-buttons): TRANSMITTERS RECEIVERS RNK-02 RNL-01 ROP-01 RWL-01 2channel button Radio 1-channel Radio lighting radio transmitter foot transmitter radio receiver switch RNK-04 RTI-01 ROP-02 RWG-01 4-channel button IR/EXTA FREE 2-channel Remote control Press PROG push-button of ROM-01 device Press and release transmitters first Press and release the second transmitters radio transmitter transceiver radio receiver socket for a longer time until LED red diode switches on push-button. LED red diode switches on push-button. LED red diode switches on (constant signal). Next release PROG push-button. (first signal pulsates, (the signal pulsates) and next it switches P-256/8 RNM-10 RDP-01 SRP-02 next the signal is constant). off - THE TRANSMITTER IS ADDED. 8-channel 4-channel radio 1-channel Radio roller blinds remote control modular transmitter radio dimmer controller TIME mode (one push-button): P-257/4 RNP-01 ROB-01/12-24V SRP-03 4-channel 4-channel Radio Central radio roller remote control radio transmitter gate controller blinds controller P-257/2 RNP-02 ROM-01 ROM-10 2-channel 4-channel 1-channel radio 2-channel remote control radio transmitter modular receiver radio modular receiver Press PROG push-button of ROM-01 device Press PROG push-button of ROM-01 device Press and release the same transmitters RCR-01 RXM-01 for a longer time till LED red diode switches on and then release it. LED red diode switches push-button. LED red diode switches on Radio RS-485/EXTA FREE (constant signal). Next release PROG push-button. on (first signal pulsates, (signal pulsates) and then switches off - motion sensor Transceiver next the signal is constant). THE TRANSMITTER IS ADDED. ACCESSORIES An exemplary programming procedure with the use of P-257/2 remote controller. The procedure for the rest of radio EXTA FREE transmitters is analogous. ANT-01 RTN-01 CAUTION: Every transmitter can cooperate with ROM-01 in a different mode, depending on how they were added to the device. External antenna Retransmitter One transmitter can be added during one programming cycle. Full memory is signalled with pulsating LED red diode. VER. 004 11.07.2011