RZB-02 WIRELESS CONTROL SET CoNNECtioN RDP-01 MouNtiNG - LIGHTING WITH DIMMING FUNCTION MANUAL INSTRUCTION 1. Disconnect power supply by the phase fuse, the circuit-breaker or the switch-disconnector combined to the proper circuit. 2. Check if there is no voltage on connec- tion cables by means of a special measure ZAMEL Sp. z o.o. equipment. 3. Connect the cables with the terminals in ac- cordance with the installing diagram. ul. Zielona 27, 43-200 Pszczyna, Poland 4. Install RDP-01 device in installation cable box. tel. +48 (32) 210 46 65, fax +48 (32) 210 80 04 5. Switch on the power supply from the mains. www.zamelcet.com, e-mail: marketing zamel.pl DESCRiPtioN tECHNiCAL DA t A RNK-02 RDP-01 RDP-01 dimmer cooperates with light bulbs, compact fluorescent lamps powe- Input (supply) terminals: - L, N red by electronic or toroidal power supply Input rated voltage: 3 V DC (CR2032 battery) 230 V AC transformers. The device has different CAPACitY RNK-02 FuNCtioNiNG, MouNtiNG Battery life: 3 5 years - functions: a traditional lighting dimmer Input voltage tolerance: - -15 +10 % function, time control functions (staircase By pressing the button, the transmitter sends a 250W 250W time delay switch), comfort functions (me- Nominal frequency: - 50 / 60 Hz signal with 868,32 MHz frequency which controls mory of adjusted luminous density level). EXTA FREE receivers. Device programming Nominal power consumption: - 0,5 W procedure (adding a transmitter to a receiv- 250W 250W Number of operation modes: - 5 ers memory) is described in particular EXt A Number of channels: 2 1 FREE manual instructions. The device range (up to 250 m depending on a receiver) can be in- Transmission: radio 868,32 MHz creased by means of a retransmitter or few RTN- Coding way: unidirectional APPLiCAtioN FEAtuRES 01 retransmitters. The device can be mounted in Coding: addressing transmission any place by means of double-sided adhesive complete set of wireless control Maximum number of transmitters: - 32 tape or two wall plugs (5x(3x30) mm. (2channel button radio transmitter Range: up to 250 m in the open area up to 230 m in the open area Mounting by means of wall plugs: RNK-02 and 1-channel radio flash dim- Time adjustment: - 1 sec 18 hours (every 1 sec.) 1. Remove the button - to do it press the button mer RDP-01), on one side, and on the other side put a screw- Optic signalling of transmitters operation: LED red diode lighting operation control - switch on/ driver into a slot and lift up the button. Receivers output clamps: - , N switch off, brightening and dimming, 2. Find a place on the wall to mount the transmit- cooperation with light bulbs, fluores- Maximum output load: - 250 W ter, make two holes corresponding mounting cent lamps powered by electronic or Number of terminal clamps: - 4 holes from the transmitters base. toroidal transformer, 2 3. Set wall plugs in the holes. Section of connecting cables: - do 2,5 mm memory of luminous density level, 4. Fix the base by means of screwing screws into o Ambient temperature range: -10 +55 C wide range of operation (up to 180 m), wall plugs. Operating position: free 5. Place the button again. operation is optically signalled, low current consumption, possibility of Casing mounting: wall plugs, double-sided adhesive tape installation cable box 60 mm BAttERY CHANGE constant work, Casing protection degree: IP20 (EN 60529) Battery discharge status is signalled by sev- possibility of widening operation range Protection level: III II eral LED red diode flashes during transmis- by means of RTN-01 retransmitter. sion time. Overvoltage category: - II 1. Remove the button (as in point 1 of mounting). Pollution degree: 2 2. By means of a screwdriver lever up the printed- Surge voltage: - 1 kV (EN 61000-4-5) circuit board releasing the bottom latch (Fig. 2), and remove it from the base. Dimensions: 90 x 80 x 11,5 mm 47,5 x 47,5 x 20 mm 3. Remove the battery from the latch. Weight: 0,038 kg 0,040 kg 4. Mount a new battery. Watch battery polari- ETSI EN 300 220-1, EN 60669, EN 60950, sation marked on the latch. Wrong battery Reference standard: The device is designed for ETSI EN 300 220-2 EN 61000 mounting may cause device damage. single-phase installation and 5. Put the removed printed-circuit board back in Radio flush dimmer RDP-01 operates as must be installed in accord- the base. ance with standards valid in a a receiver of 2-channel button radio 6. Put back the button. APPEARANCE particular country. The device transmitter RNK-02 (switch on/switch off should be connected accord- control, lighting source brightening/dimming). CAutioN: CAutioN ing to the details included in The above mentioned transmitters While changing the battery, it is suggested to this operating manual. Installation, connection Receivers input (supply) terminals ( , N) can also control operation of radio lighting The ZAMEL company press any of the buttons for about 5 seconds and control should be carried out by a qualified switch RWL-01. devices which are before putting it into a latch. Next press trans- electrician staff, who act in accordance with the Input (supply) terminals (L, N) characterised with this sign mission button several times to check its op- service manual and the device functions. can cooperate eration. if the transmitter does not work prop- In case of casing dismantling an electric shock with each other. erly repeat the battery change procedure. may occur, and the guarantee is lost then. Before installation make sure the connection cables are Optic signalling of receivers operation not under voltage. The cruciform head screwdriv- er 3,5 mm should be used to instal the device. Im- WARRANtY CARD Programming push-button proper transport, storage, and use of the device influence its wrong functioning. It is not advisable There is 24 months guarantee on the product Optic signalling of transmitters operation to instal the device in the following cases: if any 1. ZAMEL provides a two-year warranty for its products. device part is missing or the device is damaged 2. The ZAMEL warranty does not cover: a) mechanical defects resulting from transport, loading / unloading or other circumstances or deformed. In case of improper functioning of b) defects resulting from incorrect installation or operation of ZAMEL products c) defects resulting from any changes made by CUS- the device contact the producer. Push-button TOMERS or third parties, to products sold or equipment necessary for the correct operation of products sold d) defects resulting from force majeure or other aleatory events for which ZAMEL is not liable e) power supply (batteries) to be equipped with a device in the moment of sale (if they appear) 3. All complaints in relation to the warranty must be provided by the CUSTOMER in writing to the retailer after discovering a defect. The symbol means selective 4. ZAMEL will review complaints in accordance with existing regulations. collecting of electrical and electronic 5. The way a complaint is settled, e.g. replacement of the product, repair or refund, is left to the discretion of ZAMEL. 6. Guarantee does not exclude, does not limit, nor does it suspend the rights of the PURCHASER resulting from the discrepancy equipment. between the goods and the contract. It is forbidden to put the used equipment together with other waste. Salesman stamp and signature, date of sale VER. 003 20.05.2011RDP-01 oPERAtioN tiME PRoGRAMMiNG RDP-01 can operate in five modes: 1s 2s ns CoMFoRt oNE PuSH-ButtoN tWo PuSH-ButtoN tiME (Available only in coop- Pressing the programmed SWitCH oN push-button: The device after press- eration with 4 push-button push-button shortly (<0.8 pressing the programmed ing the push-button transmitter). In this mode sec.) causes the dimmer push-button shortly (<0.8 switches on according the following two functions to operate in the range sec.) causes the lighting to the adjusted time are realised: of switch on/switch off (to the last switches on (the last adjustment of (tp), then it switches off Press PROG push-button of RDP-01 device for a longer time till Press PROG push-button of RDP-01 After the adjusted time is adjustment of lighting luminous den- lighting luminous density level), how- automatically. Another pressing of LED red diode switches on (constant signal). Next release PROG device and then release it. LED red diode finished (the number of LED sity level), however pressing the pro- ever pressing the programmed push- the push-button during time count- push-button. Wait (for about 5 seconds) till LED red diode switches switches off and then switches on red diode flashes) press grammed push-button longer (>0.8 button longer (>0.8 sec.) causes light- down causes the lighting is switched on (first signal pulsates, next the signal is constant). (signal pulsates). Every LED diode pulse PROG push-button and then sec.) causes alternate lighting bright- ing brightening (to the maximum level). off before adjusted time finishes. equals 1 second. release it - TIME IS ADDED. ening - dimming. SWitCH oFF push-button: Default settings - 15 seconds. pressing the programmed Maximum time is 18 hours. push-button shortly (<0.8 CAutioN Adjusted time cannot sec.) causes the light- be deleted. ing switches off, however pressing the programmed push-but- REMotE CoNtRoLS DELEtioN level level ton longer (>0.8 sec.) causes lighting memory memory level dimming (to the minimum level). memory level memory level memory level memory Press PROG push-button of RDP-01 After 5 seconds LED red diode switches on Release the push-button in RDP-01 - level memory device for a longer time. (signal pulsates) and then it switches off. MEMORY IS DELETED. CooPERA tioN AND oPERA tiNG RANGE Symbol RoP-01 RoP-02 RoB-01 SRP-02 SRP-03 RWG-01 RWL-01 RoM-01 RoM-10 RDP-01 RtN-01 RNK-02 180 m 200 m 200 m 200 m 200 m 250 m 180 m 250 m 250 m 180 m 250 m REMotE CoNtRoLS PRoGRAMMiNG RNK-04 180 m 200 m 200 m 200 m 200 m 250 m 180 m 250 m 250 m 180 m 250 m CoMFoRt mode: P-256/8 230 m 250 m 250 m 250 m 250 m 300 m 200 m 300 m 300 m 230 m 300 m P-257/4 (2) 180 m 200 m 200 m 200 m 200 m 250 m 180 m 250 m 250 m 180 m 250 m RNM-10 230 m 250 m 250 m 250 m 250 m 300 m 200 m 300 m 300 m 230 m 300 m RNP-01 160 m 180 m 180 m 180 m 180 m 200 m 160 m 200 m 200 m 160 m 200 m RNP-02 160 m 180 m 180 m 180 m 180 m 200 m 160 m 200 m 200 m 160 m 200 m RNL-01 160 m 180 m 180 m lack* lack* 200 m 160 m 200 m 200 m 160 m 200 m Press RNK-04 Press PROG push-button of RDP-01 device Release transmitters push- Press the same transmitters push- RtN-01 200 m 200 m 200 m 200 m 200 m 250 m 200 m 250 m 250 m 200 m 250 m transmitters for a longer time until LED red diode switches on button. LED red diode switches -button and release it. LED red diode RCR-01 160 m 180 m 180 m lack* lack* 200 m 160 m 200 m 200 m 160 m 200 m push-button for (constant signal). Next release PROG push-button. on (first signal pulsates, switches on (the signal pulsates) and a longer time. next the signal is constant). next it switches off - Rti-01 160 m 180 m 180 m 180 m 180 m 200 m 160 m 200 m 200 m 160 m 200 m THE TRANSMITTER IS ADDED. oNE PuSH-ButtoN mode: RXM-01 230 m 250 m 250 m 250 m 250 m 300 m 200 m 300 m 300 m 230 m 300 m * - 1-channel transmitters do not cooperate with roller blind controllers. CAUTION: The given range concerns open area - an ideal condition without any natural or artificial obstacles. If there are some obstacles between a transmitter and a receiver, it is advisable to decrease the range according to: wood and plaster: from 5 to 20 %, bricks: from 10 to 40 %, reinforced concrete: from 40 to 80 %, metal: from 90 to 100%, glass: from 10 to 20 %, over- and underground medium and high electrical power lines, radio and television transmitters, GSM transmitters set close to a device system have also a negative influence on the range. tRANSMittERS RECEiVERS Press PROG push-button of RDP-01 device for Press the transmitters push-button Release transmitters push-button. LED red RNK-02 RNL-01 RoP-01 RWL-01 a longer time until LED red diode switches on for a longer time. LED red diode switches diode switches on (the signal pulsates), next 2channel button Radio 1-channel Radio lighting (constant signal). Next release PROG push-button. on (first signal pulsates, the LED red diode switches off - it means radio transmitter foot transmitter radio receiver switch next the signal is constant). the TRANSMITTER IS ADDED. SWitCH oN/SWitCH oFF mode (two push-buttons): RNK-04 Rti-01 RoP-02 RWG-01 4-channel button IR/EXTA FREE 2-channel Remote control radio transmitter transceiver radio receiver socket P-256/8 RNM-10 RDP-01 SRP-02 8-channel 4-channel radio 1-channel Radio roller blinds Press PROG push-button of RDP-01 device remote controller modular transmitter radio dimmer controller Press and release transmitters first Press and release the second transmitters for a longer time until LED red diode switches on push-button. LED red diode switches on push-button. LED red diode switches on P-257/4 RNP-01 RoB-01/12-24V SRP-03 (constant signal). Next release PROG push-button. (first signal pulsates, (the signal pulsates) and next it switches 4-channel 4-channel Radio Central radio roller next the signal is constant). off - THE TRANSMITTER IS ADDED. tiME mode (one push-button): remote controller radio transmitter gate controller blinds controller P-257/2 RNP-02 RoM-01 RoM-10 2-channel 4-channel 1-channel radio 2-channel remote controller radio transmitter modular receiver radio modular receiver RCR-01 RXM-01 Press and then release transmitters Press and release the same transmitters Press PROG push-button of RDP-01 device for Radio Translator push-button.LED red diode switches on push-button. LED red diode switches on a longer time till LED red diode switches on motion sensor RS-485/EXTA FREE (first signal pulsates, (signal pulsates) and then switches off - (constant signal). Next release PROG push-button. ACCESSoRiES next the signal is constant). THE TRANSMITTER IS ADDED. ANt -01 RtN-01 CAutioN: Every transmitter can cooperate with RDP-01 in a different mode, depending on how they were added to the device. External antenna Retransmitter one transmitter can be added during one programming cycle. Full memory is signalled with pulsating LED red diode. VER. 003 20.05.2011 95% 0%