FT2232HP/FT2233HP Datasheet Datasheet Version 1.0 Document No.: FT 001474 Clearance No.: FTDI 556 Future Technology Devices International Ltd FT2233HP/FT2232HP (High Speed USB Bridge with Type-C/PD3.0 Controller) The FT2233HP/FT2232HP is a Hi-Speed USB device Optional traffic TX/RX indicators can be added with with a Type-C/PD 3.0 controller that fully supports LEDs. the latest USB Type-C and Power Delivery (PD) Adjustable receive buffer timeout. standards enabling support for power negotiation Support for USB suspend and resume conditions via with the ability to sink or source current to a USB PWREN , SUSPEND and RI pins. host device. The USB bridge function delivers 2 FTDI FT232R/FT-X style, asynchronous serial UART independent channels compatible with the FT2232H interface option with full hardware handshaking and Dual Hi-speed USB to multipurpose UART/MPSSE modem interface signals. solution. Fully assisted hardware or X-On / X-Off software handshaking. The FT2233HP/FT2232HP has the following UART Interface supports 7/8 bit data, 1/2 stop bits, advanced features: and Odd/Even/Mark/Space/No Parity. Support PD specification Rev 3.0. Auto-transmit enable control for RS485 serial Port 1 mode configuration for Sink or Dual-role applications using TXDEN pin through external Port 2 works as Sink, supporting charge EEPROM setting. through to port1 (FT2233HPQ and FT2233HPL Operational configuration mode and USB Description only ) strings configurable in external EEPROM over the Support 5V3A, 9V3A, 12V3A, 15V3A and 20V3A USB interface. PDOs as sink or source Type-C/PD Physical Low operating and USB suspend current. Layer Protocol Configurable I/O drive strength (4, 8, 12 or 16mA) PD policy engine using 32-bit RISC controller and slew rate. with 8kB data RAM and 48kB code ROM USB Bulk data transfer mode (512 byte packets in PD mode configuration through external High Speed mode). EEPROM Dedicated Windows DLLs available for USB to SPI, 2 Options to use external MCU controlling PD and USB to I C applications. policy through I2C interface +3.3V single supply operating voltage range. USB to dual serial ports with a variety of +3.3V I/O interfacing. configurations. Highly integrated design includes +1.2V LDO Entire USB protocol handled on the chip. No regulator for VCORE, integrated POR function and on USB specific firmware programming required. chip clock multiplier PLL (12MHz 480MHz). USB 2.0 High Speed (480Mbits/Second) and Extended -40C to 85C industrial operating Full Speed (12Mbits/Second) compatible. temperature range. Two Multi-Protocol Synchronous Serial Engine Available in Pb-free QFN-76/QFN-68/LQDP-80 (MPSSE) on channel A and channel B, to package (RoHS compliant) simplify synchronous serial protocol (USB to 2 JTAG, I C, SPI or bit-bang) design. Independent Baud rate generators. RS232/RS422/RS485 UART Transfer Data Rate up to 12Mbaud. (RS232 Data Rate limited by external level shifter). FTDIs royalty-free Virtual Com Port (VCP) and Direct (D2XX) drivers eliminate the requirement for USB driver development in most cases. Copyright Future Technology Devices International Limited 1 FT2232HP/FT2233HP Datasheet Datasheet Version 1.0 Document No.: FT 001474 Clearance No.: FTDI 556 1 Typical Applications USB bridge with Type-C/PD (chargers and Numerous combinations of two channels. devices) Upgrading Legacy Peripheral Designs to USB High-power application via USB PD and/or Field Upgradable USB Products Type-C port Cellular and cordless phone USB data transfer Get power from USB device functions, e.g. cables and interfaces. portable USB host needs charging when USB is Interfacing MCU / PLD / FPGA based designs to connected. USB Single chip USB to two channels UART (RS232, PDA to USB data transfer RS422 or RS485) or Bit-Bang interfaces. USB Smart Card Readers Single chip USB to 2 JTAG channels USB Instrumentation Single chip USB to one JTAG channel and one USB Industrial Control UART. USB FLASH Card Reader / Writers Single chip USB to one SPI channel and one Set Top Box PC USB interface UART. USB Digital Camera Interface Single chip USB to two SPI channels. USB Bar Code Readers Single chip USB to two Bit-Bang channels. Single chip USB to one SPI channel and one JTAG channel. 2 Single chip USB to two I C channels. 1.1 Driver Support The FT2233HP/FT2232HP requires USB drivers (listed below), available for free at