FT260 HID-CLASS USB TO UART/I2C BRIDGE IC Version 1.1 Document No.: FT 001272 Clearance No.: FTDI 484 Future Technology Devices International Ltd. FT260 2 (HID-class USB to UART/I C Bridge IC) 2 FT260 is a HID-class USB to I C/UART interface Fully integrated oscillator PLL with no external Device Controller with the following advanced crystal required features: On-chip eFUSE for USB Vendor ID (VID), 2 Single chip USB to UART/I C bridge with Product ID (PID), and other vendor specific standard Human Interface Device (HID) class parameters. support Unique USB serial number generation engine USB2.0 compliant Full Speed device with entire and programming path to external EEPROM. USB protocol handled on the chip. Integrated 5V-3.3V-1.8V level converter for Support 2 USB HID Interfaces, each USB I/O. corresponding to the on-chip physical +5V USB VBUS detection engine 2 interfaces, I C and UART USB Power Configurations supports bus- Pin configuration of enabling HID interface for powered, self-powered and bus-powered with variety of application power switching. 2 HID over I C specification support USB2.0 Low operating and suspend current 2 Configurable I C Master Interface controller 24mA (active-typ) and 385A (suspend-typ). 2 conforming to I C v2.1 and v3.0 specification. True 3.3V CMOS drive output and TTL input. 2 Support 4 speed modes defined in I C-bus (operates down to 1V8 with external pull-ups) Specification, standard mode (SM), fast mode Multiple I/O operating voltage level +3.3V, (FM), Fast mode plus (FM+), and High Speed +2.5V, +1.8V mode (HS) pin output drive strength 4 mA(min) and 16 Robust FTDI UART controller with hardware and mA(max) software flow control Integrated power-on-reset circuit. Data transfer rate from 1.2 Kbuad to 12 Mbaud (RS422, RS485, RS232) at TTL levels USB Battery Charger Detection. Configurable GPIOs can be easily controlled by UHCI / OHCI / EHCI / XHCI host controller software applications under HID class via the compatible. USB bus Extended operating temperature range -40 to 85C. Available in compact Pb-free 28 Pin WQFN or TSSOP packages (RoHS compliant). Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Future Technology Devices International Ltd will not accept any claim for damages howsoever arising as a result of use or failure of this product. Your statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in which the failure of the product might reasonably be expected to result in personal injury. This document provides preliminary information that may be subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH United Kingdom. Scotland Registered Company Number: SC136640 Copyright Future Technology Devices International Limited 1 FT260 HID-CLASS USB TO UART/I2C BRIDGE IC Version 1.1 Document No.: FT 001272 Clearance No.: FTDI 484 1 Typical Applications HID class Device controller USB to RS232/RS422/RS485 Converters USB to HID-over-I2C Bridge Interfacing MCU/PLD/FPGA based designs to USB 2 USB to I C master controller USB Instrumentation 1.1 Driver Support The USB Human Interface Device (HID) class is natively supported by most operation systems. A custom driver is not required to be installed for the FT260. Windows 10 32, 64-bit Windows 8.1 32, 64-bit Windows 8 32, 64-bit Windows 7 32, 64-bit Windows Vista and Vista 64-bit Windows XP and XP 64-bit Windows CE 4.2, 5.0, 5.2, 6.0 Windows Server 2008, 2003, 2000 Windows Embedded Operating Systems Mac OS X Linux Android 1.2 Part Numbers Part Number Package FT260Q-x 28 Pin WQFN FT260S-x 28 Pin TSSOP Note: Packing codes for x is: - R: Taped and Reel, 2,500pcs per reel - T: Tray packing, 490pcs per tray (WQFN only) - U: Tube packing, 50pcs per tube (TSSOP only) For example: FT260Q-R is 2,500pcs taped and reel packing Copyright Future Technology Devices International Limited 2