EZ-PD CCG2 Datasheet USB Type-C Port Controller USB Type-C Port Controller General Description EZ-PD CCG2 is a USB Type-C controller that complies with the latest USB Type-C and PD standards. EZ-PD CCG2 provides a complete USB Type-C and U1SB Power Delivery port control solution for passive cables, active cables, and powered accessories. It can also be used in many upstream and downstream facing port applications. EZ-PD CCG2 uses Cypresss proprietary M0S8 technology with a 32-bit, 48-MHz Arm Cortex -M0 processor with 32-KB flash and integrates a complete Type-C Transceiver including the Type-C termination resistors R , R and R . P D A Type-C Support Applications Integrated transceiver (baseband PHY) USB Type-C EMCA cables Integrated UFP (R ), EMCA (R ) termination resistors, and D A USB Type-C powered accessories current sources for DFP (R ) P USB Type-C upstream facing ports Supports one USB Type-C port USB Type-C downstream facing ports Low-Power Operation Features 2.7-V to 5.5-V operation Two independent VCONN rails with integrated isolation 32-bit MCU Subsystem between the two 48-MHz ARM Cortex-M0 CPU Independent supply voltage pin for GPIO that allows 1.71-V to 32-KB Flash 5.5-V signaling on the I/Os 4-KB SRAM Reset: 1.0 A, Deep Sleep: 2.5 A, Sleep: 2.0 mA In-system reprogrammable System-Level ESD on CC and VCONN Pins Integrated Digital Blocks 8-kV Contact Discharge and 15-kV Air Gap Discharge based Integrated timers and counters to meet response times on IEC61000-4-2 level 4C required by the USB-PD protocol Packages Run-time reconfigurable serial communication block (SCB) 2 1.63 mm 2.03 mm, 20-ball wafer-level CSP (WLCSP) with with reconfigurable I C, SPI, or UART functionality 0.4-mm ball pitch Clocks and Oscillators 2.5 mm 3.5 mm 0.6 mm 14-pin DFN Integrated oscillator eliminating the need for external clock 4.0 mm 4.0 mm, 0.55 mm 24-pin QFN Supports industrial (40 C to +85 C) and extended industrial ( 40 C to +105 C) temperature ranges Logic Block Diagram CCG2: USB Type-C Cable Controller MCU Subsystem I/O Subsystem Integrated Digital Blocks 5 CC 1 TCPWM VCONN1 2 SCB 2 (I C, SPI, UART) CORTEX-M0 VCONN2 2 SCB 48 MHz 2 (I C, SPI, UART) VDDIO 6 GPIO Profiles and Port Configurations Flash Baseband MAC (32 KB) Baseband PHY SRAM 3 4 Integrated R , R , d a (4 KB) 7 and R p Serial Wire Debug 1 Timer, counter, pulse-width modulation block 2 2 Serial communication block configurable as UART, SPI, or I C 3 Termination resistor denoting a UFP 4 Termination resistor denoting an EMCA 5 Configuration Channel 6 General-purpose input/output 7 Current Sources to indicate a DFP Cypress Semiconductor Corporation 198 Champion Court San Jose, CA 95134-1709 408-943-2600 Document Number: 001-93912 Rev. *M Revised July 11, 2018 Advanced High-Performance Bus (AHB) Programmable IO MatrixEZ-PD CCG2 Datasheet Available Firmware and Software Tools EZ-PD Configuration Utility The EZ-PD Configuration Utility is a GUI-based Microsoft Windows application developed by Cypress to guide a CCGx user through the process of configuring and programming the chip. The utility allows users to: 1. Select and configure the parameters they want to modify 2. Program the resulting configuration onto the target CCGx device. The utility works with the Cypress supplied CCG1, CCG2, CCG3, and CCG4 kits, which host the CCGx controllers along with a USB interface. This version of the EZ-PD Configuration Utility supports configuration and firmware update operations on CCGx controllers implementing EMCA and Display Dongle applications. Support for other applications, such as Power Adapters and Notebook port controllers, will be provided in later versions of the utility. You can download the EZ-PD Configuration Utility and its associated documentation at the following link: