Series PVD13NPbF
Microelectronic Power IC
HEXFET Power MOSFET Photovoltaic Relay
Single-Pole, Normally-Open, 0-100V DC, 550mA
General Description Features
The PVD13 Series DC Relay (PVD) is a single-pole,
Bounce-Free Operation
normally open, solid-state replacement for
10
10 Off-State Resistance
electromechanical relays used for general purpose
1,000 V/sec dv/dt
switching of analog signals. It utilizes International
Rectifiers HEXFET power MOSFET as the output
5 mA Input Sensitivity
switch, driven by an integrated circuit photovoltaic
4,000 V I/O Isolation
RMS
generator of novel construction. The output switch is
Solid-State Reliability
controlled by radiation from a GaAlAs light emitting
UL Recognized
diode (LED), which is optically isolated from the
ESD Tolerance:
photovoltaic generator.
4000V Human Body Model
The PVD13 Series overcomes the limitations of both
500V Machine Model
conventional electromechanical and reed relays by
offering the solid state advantages of long life, fast
operating speed, low pick up power, bounce-free
operation, low thermal offset voltages and miniature
package. These advantages allow product
improvement and design innovations in many
applications such as process control, multiplexing,
automatic test equipment and data acquisition.
The PVD13 can switch analog signals from
thermocouple level to 100 Volts peak DC. Signal
frequencies into the RF range are easily controlled
and switching rates up to 450Hz are achievable. The
extremely small thermally generated offset voltages
allow increased measurement accuracies.
These relays are packaged in 8-pin, molded DIP
packages and available with either thru-hole or
surface-mount (gull-wing) leads, in plastic shipping
tubes.
Part Identification
Applications
PVD1352NPbF
Process Control
thru-hole
PVD1354NPbF
Data Acquisition
Test Equipment
surface-mount
PVD1352NSPbF
Multiplexing and Scanning
PVD1354NSPbF (gull-wing)
(HEXFET is the registered trademark for International Rectifier Power MOSFETs)
1 www.irf.com 2015 International Rectifier Submit Datasheet Feedback April 29, 2015Series PVD13NPbF
Electrical Specifications (-40C T +85C unless otherwise specified)
A
INPUT CHARACTERISTICS PVD1352N PVD1354N Units
Minimum Control Current (see figures 1 and 2) DC
For 500mA Continuous Load Current 2 mA@25C
For 550mA Continuous Load Current 5 mA@40C
For 350mA Continuous Load Current 5 mA@85C
Maximum Control Current for Off-State Resistance at 25C 10 A(DC)
Control Current Range (Caution: current limit input LED. See figure 6) 2.0 to 25 mA(DC)
Maximum Reverse Voltage 6.0 V(DC)
OUTPUT CHARACTERISTICS PVD1352N PVD1354N Units
Operating Voltage Range 0 to + 100 V
(PEAK)
Maxiumum Load Current 40C I LED 5mA 550
mA(DC)
Response Time @25C (see figures 7 and 8)
Max. T @ 12mA Control, 50 mA Load, 100 VDC 150 s
(on)
Max. T @ 12mA Control, 50 mA Load, 100 VDC 125 s
(off)
Max. On-state Resistance 25C (Pulsed) (fig. 4) 200 mA Load, 5mA Control 1.5
8 10
Min. Off-state Resistance 25C @ 80 VDC (see figure 5) 10 10
Max. Thermal Offset Voltage @ 5.0mA Control 0.2 volts
Min. Off-State dv/dt 1000 V/s
Typical Output Capacitance 20 pF @ 50VDC
GENERAL CHARACTERISTICS (PVD1352N and PVD1354N) Units
Dielectric Strength: Input-Output 4000 V
RMS
12
Insulation Resistance: Input-Output @ 90V 10 @ 25C - 50% RH
DC
Maximum Capacitance: Input-Output 1.0 pF
Max. Pin Soldering Temperature (1.6mm below seating plane, 10 seconds max.) +260
Ambient Temperature Range: Operating -40 to +85 C
Storage -40 to +100
International Rectifier does not recommend the use of this product in aerospace, avionics, military or life support applications.
Users of this International Rectifier product in such applications assume all risks of such use and indemnify International
Rectifier against all damages resulting from such use.
2 www.irf.com 2015 International Rectifier Submit Datasheet Feedback April 29, 2015