Series PVD13NPbF Microelectronic Power IC HEXFET Power MOSFET Photovoltaic Relay Single-Pole, Normally-Open, 0-100V DC, 550mA General Description Features The PVD13 Series DC Relay (PVD) is a single-pole, Bounce-Free Operation normally open, solid-state replacement for 10 10 Off-State Resistance electromechanical relays used for general purpose 1,000 V/sec dv/dt switching of analog signals. It utilizes International Rectifiers HEXFET power MOSFET as the output 5 mA Input Sensitivity switch, driven by an integrated circuit photovoltaic 4,000 V I/O Isolation RMS generator of novel construction. The output switch is Solid-State Reliability controlled by radiation from a GaAlAs light emitting UL Recognized diode (LED), which is optically isolated from the ESD Tolerance: photovoltaic generator. 4000V Human Body Model The PVD13 Series overcomes the limitations of both 500V Machine Model conventional electromechanical and reed relays by offering the solid state advantages of long life, fast operating speed, low pick up power, bounce-free operation, low thermal offset voltages and miniature package. These advantages allow product improvement and design innovations in many applications such as process control, multiplexing, automatic test equipment and data acquisition. The PVD13 can switch analog signals from thermocouple level to 100 Volts peak DC. Signal frequencies into the RF range are easily controlled and switching rates up to 450Hz are achievable. The extremely small thermally generated offset voltages allow increased measurement accuracies. These relays are packaged in 8-pin, molded DIP packages and available with either thru-hole or surface-mount (gull-wing) leads, in plastic shipping tubes. Part Identification Applications PVD1352NPbF Process Control thru-hole PVD1354NPbF Data Acquisition Test Equipment surface-mount PVD1352NSPbF Multiplexing and Scanning PVD1354NSPbF (gull-wing) (HEXFET is the registered trademark for International Rectifier Power MOSFETs) 1 www.irf.com 2015 International Rectifier Submit Datasheet Feedback April 29, 2015Series PVD13NPbF Electrical Specifications (-40C T +85C unless otherwise specified) A INPUT CHARACTERISTICS PVD1352N PVD1354N Units Minimum Control Current (see figures 1 and 2) DC For 500mA Continuous Load Current 2 mA 25C For 550mA Continuous Load Current 5 mA 40C For 350mA Continuous Load Current 5 mA 85C Maximum Control Current for Off-State Resistance at 25C 10 A(DC) Control Current Range (Caution: current limit input LED. See figure 6) 2.0 to 25 mA(DC) Maximum Reverse Voltage 6.0 V(DC) OUTPUT CHARACTERISTICS PVD1352N PVD1354N Units Operating Voltage Range 0 to + 100 V (PEAK) Maxiumum Load Current 40C I LED 5mA 550 mA(DC) Response Time 25C (see figures 7 and 8) Max. T 12mA Control, 50 mA Load, 100 VDC 150 s (on) Max. T 12mA Control, 50 mA Load, 100 VDC 125 s (off) Max. On-state Resistance 25C (Pulsed) (fig. 4) 200 mA Load, 5mA Control 1.5 8 10 Min. Off-state Resistance 25C 80 VDC (see figure 5) 10 10 Max. Thermal Offset Voltage 5.0mA Control 0.2 volts Min. Off-State dv/dt 1000 V/s Typical Output Capacitance 20 pF 50VDC GENERAL CHARACTERISTICS (PVD1352N and PVD1354N) Units Dielectric Strength: Input-Output 4000 V RMS 12 Insulation Resistance: Input-Output 90V 10 25C - 50% RH DC Maximum Capacitance: Input-Output 1.0 pF Max. Pin Soldering Temperature (1.6mm below seating plane, 10 seconds max.) +260 Ambient Temperature Range: Operating -40 to +85 C Storage -40 to +100 International Rectifier does not recommend the use of this product in aerospace, avionics, military or life support applications. Users of this International Rectifier product in such applications assume all risks of such use and indemnify International Rectifier against all damages resulting from such use. 2 www.irf.com 2015 International Rectifier Submit Datasheet Feedback April 29, 2015